background image

S i r e n

P l u g

Fig 17

LED

Wood Trim Panel

Fig 15

(E-36) 3 Series (318ti & Z3 )

1.

 Mount the siren in your engine compartment.

2.

 Run the wires from the siren to the factory 2 pin siren plug.

    This factory siren plug can be located in 2 spots:

   

a.

 Behind right-hand (passenger's) side headlight's wire loom.  

(Figure 16)

    - Trace the wiring from the headlights back to the factory siren plug.

Siren Installation

S i r e n   P l u g   B e h i n d

R i g h t   H e a d l i g h t

Fig 16

H o o d

S w i t c h

   NOTE: FOR Z3 2.8L The siren plug is located below your brake booster in

   your engine competent.

UPDATE

 

1.

 You may mount the LED in any dry location. We recommend mounting

the LED in the wood trim panel to the right of the steering column. 

(Figure 15)      

Carefully 

remove the wood trim from the panel with a sliding 

and pulling action.

2.

 Carefully drill a hole for the LED using stencil ( Figure 15).

3.

 Mount the LED in the hole and run the wires to the receiver which is now

mounted under the dash.

4.

 Plug in the LED terminal into the receiver.

Go to " Siren Installation"

6

   b.

 Below the battery terminal  between the passenger side's  firewall and

       strut tower.

 (Figure 17

)

(E-32) 7 Series

REV2  5.12.03  

bmwstx  6/10

RECIEVER

 

INSTALLATION GUIDE

automotive security systems

(E-36) 3 Series ( Except 318ti & Z3) 

Summary of Contents for BMWRTX











Reviews: