Stellar Hearth IGL26 Installation And Operation Manual Download Page 14

Stellar Hearth Products 

FIREPLACE DRAFT TEST METHOD 

To determine if your fireplace is drafting properly, turn the log set on.  After log set operation has been burning for 
about 10 minutes, place a match or smoke stick along the top and sides of the fireplace opening.  If the flame or 
smoke is not pulled into the fireplace, 

then the fireplace is not venting properly

.  At this point, the damper stop 

should be adjusted so that the damper opening is increased.  If the problem remains after the open area of the 
damper is increased, then the fireplace system should be professionally inspected to determine if your firebox/
chimney is venting properly.  

9B  -  FIREPLACE DRAFT TEST METHOD 

Page 14 

 
WARNING: 

BURN HAZARD!  

THE GLASS LOGS WILL REMAIN HOT FOR SOME TIME AFTER USE.  YOU 
MUST MAINTAIN THE GLASS LOG LAYOUT AS SHOWN IN THIS MANUAL TO 
ENSURE PROPER OPERATION OF THE LOG SET.  ANY HANDLING OF  

          

THE GLASS LOGS, GLASS BEADS, OR BURNER MUST BE DONE WITH  

   

 

         HEAT-RESISTANT GLOVES TO BE SAFE, AND ONLY WHEN THE PRODUCT  

 

         HAS COOLED DOWN TO ROOM TEMPERATURE.

 

9 -  OPERATING INSTRUCTIONS 

1.  With the gas supply turned on, simply locate the on/off switch in the left-hand side of the front grille.  Turn the 

switch to the “ON” position.  The unit will begin sparking and light itself within a few seconds.  (Depending on 
how much air is in the line, you may have to repeat this step several times in order to clear the gas line of air 
and introduce the gas to the insert).  

2.  To operate the Moonbeam

TM

 Accent Lights, simply locate the on/off light switch on the right-hand side of the 

front grille, and turn to the “ON” position.   

3.  When not operating the appliance for an extended period of time, it is recommended to turn off the gas supply 

at its source and unplug the power cord. 

 
CAUTION:  FOR YOUR SAFETY 
Do not use this appliance if any part has been under water.  Immediately call a 
qualified service technician to inspect the appliance and to replace any part of 

 

    the system or gas control that has been under water.    

 
Keep this appliance clear and free from combustible materials, gasoline and 
other flammable vapors and liquids. 

 

9A -  Gas Insert and Moonbeam

TM

 Accent Lights Operating Instructions 

Summary of Contents for IGL26



















Reviews: