SteelBeast PRO 2 PB Series Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 29

background image

PB2

This document is protected by copyrights.

Copying, using, or distributing without permission of JEI Group Ltd is prohibited.

8

2. SAFETY PRECAUTIONS

1. Before use

, read this Operator’s Manual and complete a training in occupational

safety and health.

2. Use only motors specified in the technical data.

3.

Use only in applications specified in this Operator’s Manual.

4. Make sure that the machine has all parts and they are genuine and not damaged.

5. Make sure that the specifications of the air (power) source are the same as those

specified on the rating plate.

6. Supply the machine with air motor only with clean and lubricated air. Make sure

that the air source has an air preparation unit that contains a filter, regulator, and

lubricator.

7. Do not pull the hose (cord). This can cause damage and serious injury.

8. Keep untrained bystanders away from the machine.

9. Before each use, ensure the correct condition of the machine, air (power) source,

supply hose (power cord, battery), coupling (plug), control parts, and tool bits.

10. Before each use, make sure that no part is cracked or loose. Make sure to

maintain correct conditions that can have an effect on the operation of the

machine.

11. Avoid accidental starts. Do not put the machine so that the motor will start. Do

not carry the machine with air motor by holding the ON/OFF lever.

12. Keep the machine dry. Do not expose the machine to rain, snow, or frost.

13. Keep the work area well-lit, clean, and free of obstacles.

14. Do not use machine near flammable materials, or in explosive environments.

15. Attach the pipe so that it will not fall or roll.

16.

Use only tool bits specified in this Operator’s Manual.

17. Do not use tool bits that are dull or damaged.

18. Attach the tool bits with two set screws. Remove wrenches from the work area

before you connect the machine to the air (power) source.

19. Use eye and ear protection, protective footwear, and protective clothing. Do not

use loose clothing.

20. Use an electric/battery motor only after you set the rotation direction switch and

operation mode switch as shown in Fig. 1. Using left rotation or impulse mode

(switches set to the opposite positions) can damage the machine.

«
...
6
7
8
9
10
...
»

Summary of Contents for PRO 2 PB Series






























Reviews:

No comments

Related manuals for PRO 2 PB Series

Brand: Rapid Pages: 6

Brand: OK-WINDER Pages: 2

Brand: JAMEC PEM Pages: 4

Brand: parktool Pages: 4

Pro Attachment PAS-225

Brand: Echo Pages: 28

Brand: XPOtool Pages: 4

Brand: Landoll Pages: 54

Brand: TAAG Pages: 5

Brand: Wacker Neuson Pages: 56

Brand: Teryair Pages: 8

Brand: Pulsar Pages: 8

Brand: Franke Pages: 89

Brand: Alemite Pages: 66

Bristle Blaster Pneumatic

Brand: Monti Pages: 268

Brand: Omega Lift Pages: 36

ShopMaster CL180JS

Brand: Delta Pages: 15

Brand: Happy Henhouse Pages: 20

Brand: Nakayama Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands