background image

Rev 3/2012 

 

18 | 

P a g e  

Part 2 

Safety Notes:  

 

1.

 

The power supply must be installed according to the local standard and with GFCI 

(Ground Fault Current Interrupter). Test the GFCI before using to confirm its security 

and validity 

2.

 

The ground for electrical appliances should be connected to fixed earth wire forever.  

3.

 

To avoid electric shock, replacing the power supply wire should be done by a 

professional electrician or distributor. Users should not change it by themselves. 

4.

 

To avoid shock, no extension power line should be used. The socket should be in the 

right position. Broken electric wire should be changed in time.  

5.

 

It is forbidden to make any change, adding, or cutting to the product. 

6.

 

It is forbidden to use the product while intoxicated.  

7.

 

Children should us the product under adult supervision. 

8.

 

Adjust the water temperature slowly from colder to warmer to avoid being scalded.  

9.

 

Stop using the product if you feel uncomfortable.  

 

 

Parameter for Steam Cabin:  

 

Rated Power: 

 

 

 

3.0KW 

Rated Voltage: 

 

 

 

Double Phase AC240V 

Rated Electric Current:   

 

16A 

Frequency:   

 

 

 

50Hz 

Power Supply: 

 

 

 

On Wall 

Rated Water Pressure:   

 

0.2 – 0.6MPa 

Water Supply: 

 

 

 

DN 15 tie-in, hot/cold water 

Water Supply Location:   

 

On Floor 

Diameter of Drainage Pipe:  

 

Φ50 (drainage pipe supplied with product) 

Length of Drainage Pipe: 

 

1000mm (the maximum length after streched) 

 

 

 

Summary of Contents for WS-112






























Reviews: