ENGLISH
13
13
3.3 Description illustrated
1. Quick-change drill chuck.
2. Locking button.
3. ON/OFF switch.
4. Speed controller.
5. Clockwise/Counter-clockwise switch.
6. Clip for belt (TM10CA).
4. Operating Instructions
4.1 Placement and Testing
ON/OFF switch (Fig. 4/Item 3)
- First fit a suitable drill bit into the tool (see 6.1).
- Connect the mains plug to a suitable socket.
- Position the drill in the position you wish to drill.
To switch on:
Press the ON/OFF switch (3)
Continuous operation:
Secure the ON/OFF switch (3) with the locking button (2).
To switch off:
Press the ON/OFF switch (3) briefly.
4.2 Changing tools
Carbon brushes
In case of excessive sparking, have the carbon brushes
checked only by a qualified electrician.
Important! The carbon brushes should not be rep laced by
anyone but a qualified electrician.
Attention! The carbon brushes should be repla
-
ced only by an authorized workshop Stayer
4.3 A
djustment
Operations
You can infinitely vary the speed whilst using the tool.
- Select the speed by applying a greater or lesser
pressure to the ON/OFF switch (3).
- Select the correct speed: The most suitable speed
depends on the workpiece, the type of use and the drill
bit used.
- Low pressure on the ON/OFF switch (3): Lower speed
(suitable for: small screws and soft materials)
- Greater pressure on the ON/OFF switch (3): Higher
speed (suitable for large/long screws and hard
materials).
Tip:
Start drilling holes at low speed. Then increase the
speed in stages.
Benefits:
- The drill bit is easier to control when starting the hole
and will not slide away.
- You avoid drilling messy holes (for example in tiles).
Preselecting the speed (Fig. 4/Item 4)
- The speed setting ring (4) enables you to define the
maximum speed. The ON/OFF switch (3) can only be
pressed to the defined maximum speed setting.
- Set the speed using the setting ring (4) on the ON/OFF
switch (3).
- Do not attempt to make this setting whilst the drill is in
use.
Clockwise/Counter-clockwise switch (Fig. 4/Item 5)
- Change switch position only when the drill is at a
standstill!
- Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (5):
*
Direction Switch position.
*
Clockwise (forwards and drill).
*
Counter-clockwise (reverse).
5. Maintenance and service instructions
5.1 Cleaning and maintenance
Always pull out the mains power plug before
starting any cleaning work.
Cleaning
- Keep all safety devices, air vents and the motor housing
free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it with
compressed air at low pressure.
- We recommend that you clean the device immediately
each time you have finished using it.
- Clean the equipment regularly with a moist cloth and
some soft soap. Do not use cleaning agents or solvents;
these could attack the plastic parts of the equipment.
Ensure that no water can seep into the device.
Maintenance
There are no parts inside the equipment which
require additional maintenance.
5.2 Repair Service
The service will advise you on the queries that you may
have about the repair and maintenance of your product,
as well as replacement parts.
Exploded views and information on spare parts can also
be found under:
Our team of technical advisors will be happy to guide
as to the acquisition, implementation and adjustment of
products and accessories.
5.3 Warranty
Warranty Card
The documents are part of the tool find the warranty card.
Must completely fill out the warranty card to apply to this
copy of the sales receipt or invoice and deliver it to your
dealer to change the corresponding acknowledgment.
NOTE! If this missing card immediately let him ask
your dealer.
Summary of Contents for TM10BA
Page 3: ...3 3 TM10BA 1 2 3 4 5 2 1 3 1 1 a ...
Page 4: ...4 4 4 5 4 2 3 4 5 3 1 6 2 5 TM10CA ...
Page 5: ...5 5 5 3 1 2 6 TM10DA ...
Page 26: ...NOTAS 26 26 ...
