stayer SCR 255 CW, Operating Instructions Manual

Page: 19 / 64

ENGLISH
19
19
This manual is consistent with the date of manufacture of your
machine, you will find information on the technical data of the
machine acquired manual check for updates of our machines
on the website:
www.grupostayer.com
1.
PROVIDED USES OF THE MACHINE
This tool has been solely and exclusively provided for:
1 Stationary works on flat and stable surface
2 Working on hard and soft wooden pieces
3 Working on chipboard pieces
4 Working on fiberboard pieces
5 Working on PVC tubes
6 Making rectilinear cuts along the length and width of the
workpiece
7 Making horizontal mitre-cuts between -45º and 45º.
8 Making vertical mitre-cuts between 90º and 45º.
Refer to the limits regarding the size of the workpiece in
corresponding chapter 11.
2.
UNPACKAGING AND ASSEMBLING
Unpackaging
1 Cut the seal and open the box.
2 Withdraw upper cardboard stoppers
3 Extract the box by firmly grasping the operating head and
the motor body using both hands so as to balance the
weight.
4 Extract the box with the accessories
5 Extract the documentation
6 Preserve the cardboard box, the stoppers there of and
the documentation permanently in an inventoried safe
environment being easily accessible and known to the
machine operator.
Packaging
Operation 1: Securing, folding and fastening the
operating head:
1
Place upper head at horizontally 0º.
2 Place upper head at vertically 90º.
3 Arrange protector such that it contacts the cutting bench.
4 Lower head to the limit and position it to be able to lock it.
5 Push lower locking button to lock the head.
Operation 2: Packaging the machine
1 Locate the cardboard box.
2 Locate documentation.
3 Firmly grasp the machine by its operating head and
motor body.
4 Place the machine over the 4 circular recesses of the
bottom of the box.
5 Store documentation of the machine.
6 Position upper cardboard stoppers.
Close the box and fix it with sealing tape.
3.
SETTING OR FASTENING THE MACHINE IN A STABLE
POSITION
1
The working area where the machine is being arranged
must mandatorily be safe.
2
Support tool in a stable position on an even surface.
3
The base of the mitre saw has four holes for firmly
fastening the machine to the working bench. It is strongly
recommended to fix the machine to the bench by means
of the pertinent screws and nuts.
4.
CONNECTION TO THE GRID, WIRING, FUSES,
SOCKET TYPE FOR THE JACK AND REQUIREMENTS
FOR GROUNDING
1 For supplying electrical power to the machine, connect the
Schuko Jack to a standard socket capable of supplying a
minimum of 2500 VA .
2 The internal wiring of the machine is completely
terminated so that no wiring is needed when installing it.
3 The machine does not have fuses although the use of a
dedicated magnetothermal switch is recommended as a
protection for the machine.
4 The machine has a class II electrical equipment so that
it does not make use of the grounding of the electrical
installation.
5.
LLUSTRATED DESCRIPTION OF THE FUNCTIONS
1 Pin for angle of lower table (mitre -45° / 45°) 2.
2 Mitre angle lock.
3 Head unlocking button.
4 Pin for locking head in the down position.
5 Head tilt adjustment (bevel -45° / 0°) (-45° / +45° for
SCR315W).
6 On/off button on the grip.
7 Blade lock
8 Locking knob for telescopic rail.
9 Telescopic rail
10 Extendible brackets
11 Depth stop
12 Set of screws for protective casing.
13 Transport handle in the down position
14 Laser guide
15 Rear bracket
16 Laser guide on/off switch
17 Locking knobs for extendible cutting guide.
18 Pin for left/right tilted cutting (only on SCR315W)
19 Tightening screws for extendible brackets
A Lower table with degree scale ruler
B Head rotation axes
C Lower blade guard
D Outlet for connection to dust collector
E Head
F Grip
6.
LIMITATIONS REGARDING ENVIRONMENTAL
CONDITIONS
The IP degree of this machine is 20. This machine is protected
against its dangerous parts being accessed by a finger and
against solid foreign particles having diameters of 12’5 mm
and more.
This machine does not have any kind of protection against the
entry of water so that its use in exterior or interior environmental
conditions with a risk of precipitations is forbidden.
7.
SETTINGS AND TESTING
Warning!
Before any intervention on the electrical tool remove jack
from power socket.
If the machine has been subject to prolonged or intense use, it
must be checked and adjusted so as to ensure the machine’s
correct quality of service and safety.
This requires knowledge, experience and special tools. The
official technical service of Stayer Iberica S.A. will carry out
that work for you in a quick thorough and inexpensive manner.
Locking in the down position
1 Start with the head raised.
2 Unlock the head by pressing the plate (3) (only on
SCR255W)
3 Lower the head to the lowest position.
4 Twist and push the pin (4) all in the way to lock the head.
When fitted correctly, the head will not be able to lift
upwards.