Default admin user name: admin
Default admin password:
(leave blank)
STEP 6
Add a new scene
Each home can create up to 20 scenes, and each scene
consists of IF/THEN/WHEN elements.
“IF”
is the conditions that will trigger this scene, up to 6
conditions are allowed in each scene, these conditions
could be “and/or” operated. The “IF” conditions could be
set according to the status of the Z-Wave devices, room
conditions or Z-Wave camera status.
“THEN”
is the actions of this scene, up to 6 actions are
allowed in each scene. The “THEN” actions could be the
actions of the Z-Wave devices, room actions or Z-Wave
camera actions.
“WHEN”
allows this scene conditions to be checked
always, every day, every week or during some time period.
Quick Installation Guide
What should I do if I have forgotten the password or the ID/Password
card is missing?
Please press the Reset button for five seconds. The camera will reset to the
factory default settings. The default video-play password is ipcam(lowercase).
What should I do if I cannot see the video remotely?
The red LED of the camera should be remain on when the camera is connected to the
Internet. If the red LED is blinking, please double check the network
connection and settings again.
I can see the video in a remote place, but the video quality is not good and
sometimes the video would disconnect and then reconnect again by itself.
It's probably because the internet bandwidth (internet speed) is not big enough.
Please try to apply for a better internet connection from your Internet Service
Provider or decrease the bandwidth setting of the camera.
What is the default admin user name/password?
Q1
Q2
Q3
Q4
Q5
Q3
Where to download the latest mCamView Z+ App?
Please scan the QRCode.
SD Card Recording
* Note: Class 10 micro SD is prerequisite
a Insert the SD card into the camera, the yellow LED on the
camera will be blinking.
b The SD card will start to do the recording once the alarm
notification is triggered. The camera will do 5 second
pre-recording to prevent the loss of the important starting
moment.
c To enable the continuous SD card recording, please enable
it inside the camera settings.
d To playback the recorded video, tap the
on the upper
right corner of the App and choose the “SD Card”. Choose
from the camera list and date/time to do the playback.
ID/Password Card
Power Adapter
Ethernet Cable
Anchors
and Screws
Ans
Ans
Ans
Ans
Ans
Bracket
Pan / Tilt Z-WAVE Smart Home Kit
Package Contents
FAQs
More FAQs, please visit
www.starvedia.com/download.html#faq
Camera
a
Tap "
+
" to add a scene.
b
Name the scene.
c
Do the scene settings.
For more details, please see the
mCamView Z+ user manual.
STEP 7
Scene Interface
The App will get alarm notification when one of the following events happened.
All the trigger events could be set and be enabled or disabled.
Please refer to the user manual for detailed settings.
[ F R O N T ]
Light Detector
Lenses
IR LED
Microphone
Reset Button
WPS Button
[ B A C K ]
Power Jack
Ethernet Jack
[ T O P ]
Micro-SD Card Slot
Micro-SD Card Indication LED
Status Indication LED
Ethernet Indication LED
[ B O T T O M ]
Bracket Screw Hole
Bracket Slots
QIG
Power Plug
4 in 1 Sensor
a Back to previous page
b Add a scene
c Remove scenes
d Tap to program the scene
e Enable/Disable this scene
f Do the scene actions
g Rename a scene or change its ICON
h Enable/Disable alarm (push) notifications
while this scene is triggered
b
c
d
e
f
g
h
a
Product View
a When the Z-Wave device changed status.
b When the scene is triggered.
c When the camera event is triggered, like the
sound or motion detection.
Alarm Notification
Internal Speaker
