manualshive.com logo in svg

Starcraft STARFLYER 2015, User Manual, Page: 90 / 152

Share
Download
Starcraft STARFLYER 2015 User Manual Download Page 90

SECTION 4

 

– TOWING & SET-UP 

STARCRAFT TOWABLE

 

 

  

 

4-40 

SCT

 

C

AMPING 

T

RAILER 

T

EAR 

D

OWN 

-

 

H

ARD 

S

IDE 

M

ODELS 

O

NLY                

Step 1 

Unlatch the first sidewall (non-door 
side).    Slowly lower the sidewall 
towards the center of the unit until it 
reaches the stowed  or travel 
position. 

 

 

 

 

 

Step 2 

Unlatch the top and bottom door 
section.  Open the upper section of 
the door to allow you to stand in the 
unit as the wall is lowered.  Unlatch 
the sidewall  (door side)  and slowly 
lower it towards the center of the 
unit until it reaches  the stowed  or 
travel position. 

 
 
 
 
 
Step 3 

Holding the roof at the grab handle, 
push up on the roof to release the 
roof latch.   Slowly lower the roof to 
the closed position. 

 

  NOTE:  Having a second 

person on the opposite side of 
the unit will ease the process of 
lowering the roof. 

 

 
 
 
 
 
 
 

 

 

 

 

 

 

CAUTION 

Keep hands and 
fingers away from the 
roof edge and the top 
of the sidewall when 
lowering 

the 

roof.   

Failure to do so may 
result in personal 
injury. 

 

Summary of Contents for STARFLYER 2015

























































































































































Reviews:

No comments