manualshive.com logo in svg

Stanley SRP 6570, User Manual

Share
Download
Stanley SRP 6570 User Manual Download Page 5

SRP 6570 User

 Manual ◄ 5

FOREWORD

PLEASE ENTER (DATA ON MACHINE TYPE PLATE)

1. MACH.-TYPE:                                                         

2. MACH.-NO.:                                                          

3. ENGINE-TYPE:                                                       

4. ENGINE-NO.:                                                         

Stanley Hydraulic Tools

3810 SE Naef Rd

Milwaukie, OR 97267

Ph: 503-659-5660

Fax: 503-652-1780

www.stanleyhydraulics.com

These instructions include:

•  Safety regulations

•  Operating instructions

•  Maintenance instructions

These instructions have been prepared for operation on the 

construction site and for the maintenance engineer.

These instructions are intended to simplify operation of the 

machine and to avoid malfunctions through improper opera-

tion.

Observing the maintenance instructions will increase the 

reliability and service life of the machine when used on the 

construction site and reduce repair costs and downtimes.

Always keep these instructions at the place of use of the ma- 

chine.

Only operate the machine as instructed and follow these 

instructions.

Do not fail to comply with all County and State safety provi-

sions, as well as the rules for safety and health.

Also observe  the corresponding rules and regulations valid in 

your country.

Stanley is not liable for the function of the machine when 

used in an improper manner and for other than the intended 

purpose.

Operating errors, improper maintenance and the use of incor-

rect operating materials are not covered by the warranty.

The above information does not extend the warranty and li-

ability conditions of business of Stanley.

We reserve us the right to make changes due to technical 

development without announcement.

Summary of Contents for SRP 6570

























Reviews:

No comments

Brands by name

Popular brands

Load more brands