19
ENGLISH (
Original Instructions)
USE
WARNING!
Always wear gloves when you change
accessories. The exposed metal parts on the tool and
accessory may become extremely hot during operation.
Please operate tool with normal load. Do not overload. Do
not abuse the tool, please refer instruction manual to use
the tool correctly.
WARNING!
Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Setting the drilling depth (FIG. A)
The depth stop is a convenient feature to ensure uniformity
in drilling depth. Loosen the side handle to adjust the depth
gauge according to the required depth. After that, tighten
the side handle.
♦ Slacken the side handle (9) by turning the grip
counter-clockwise.
♦ Set the depth stop (8) to the required position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth stop.
♦ Tighten the side handle by turning the grip clockwise.
Switching on and off (FIG. A)
WARNING!
Before plugging in to the power source, make
sure the variable speed switch can be flipped freely, and
can return to its original position once released. Please
check switch lock on position before turn on and make sure
switch lock off before plugging in to the power source.
♦ To switch the tool on, press the variable speed switch (3).
The tool speed depends on how far you press the switch.
♦ As a general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
♦ For continuous operation, press the lock-on button (2)
and release the variable speed switch.
♦ To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
WARNING!
When the user leaves, or pick up, transport,
manner and position the tool, make sure that tool is
switched off and unplugged.
Fitting drill chuck (FIG. D) (SHR263)
Optional accessory
♦ Insert the drill chuck (12) into the tool clamp (7)
according to the instructions for installing attachments.
♦ Turn the drill chuck to loosen the clamps at the front-
end of the drill-clamp, and insert the drill bit (13) into
the clamps and turn the chuck in the opposite direction.
♦ You may also use the drill chuck key to tighten the clamp.
Warning:
Never use standard chucks in the
hammer-drilling mode.
Replacing the SDS Plus Tool Holder with the
Keyless Chuck (Fig. G) (SHR264)
♦ Turn the locking collar (15) into the unlocking position
and pull the SDS Plus Tool Holder (16) off.
♦ Push the keyless chuck (17) onto the spindle and turn
the locking collar (15) to the locking position.
To replace the keyless chuck with the SDS Plus tool holder,
first remove the keyless chuck the same way the tool holder
was removed. Then place the tool holder the same way the
keyless chuck was placed making sure to turn the locking
collar to the locking position.
WARNING!
Never use standard chucks in the
hammer-drilling mode.
Selecting the Operating Mode (FIG. B)
The tool can be used in the following operating modes:
Rotary drilling:
for screw driving and for drilling
into steel, wood and plastics
Hammer drilling:
for concrete and masonry
drilling operations. Bit rotation: non-working
position used only to rotate a flat chisel into the
desired position
Hammering only:
for light chipping, chiselling and
demolition applications. In this mode the tool can
also be used as a lever to free a jammed drill bit.
1. To select the operating mode, press the mode selector
button and rotate the mode selector switch (5) until it
points to the symbol of the required mode.
2. Release the mode selector button and check that the
mode selector switch is locked in place.
WARNING!
Do not select the operating mode when
the tool is running.
Proper Hand Position (FIG. A, FIG. E)
WARNING!
To reduce the risk of serious personal
injury, ALWAYS use proper hand position as shown.
WARNING!
To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
(9), with the other hand on the main handle (1).
Rotary drilling (FIG. B, FIG. C1/C2, FIG. D, FIG. G)
♦ For drilling in steel, wood and plastics, or for screw
driving set the operating mode selector (5) to the
position.
♦ Fit the drill chuck assembly. Depending on your tool,
follow either of the following instructions:
SHR264:
Replace the SDS Plus tool holder (16) with
the keyless chuck (17).
SHR263:
Fit the drill chuck assembly (12).
♦ Insert the appropriate bits. When driving slotted head
screws always use bits with a finder sleeve.
♦ For drilling in steel, wood and plastics, set the forward/
reverse lever (4) to the forward position (Fig. C1). When
use for screw driver function, tighten screws set the
forward/reverse lever (4) to the forward position (Fig.
C1) and loose screws set the forward/reverse lever (4)
to the reverse position (Fig. C2).
WARNING!
Never use drill chucks in the hammer drilling
mode.
Hammer drilling (FIG. B)
♦ For hammer drilling in masonry and concrete, set the
operating mode selector (5) to the
position.
