background image

WET PICK-UP

Your vac contains a blowing feature. It has the capability to blow sawdust and other debris. It can be 

used to blow dust and debris out of garages or off patios and driveways. Follow the steps below to 

use your vac as a blower.
1.   Locate blowing port on your vac.

2.   Insert one end of the 1-1/4 in. x 4 ft. hose into the blowing port.

3.   Turn vac “ON”.

EMPTY THE TANK

BLOWING OPERATION

     WARNING: 

To reduce the risk of injury from accidental starting, unplug power cord before emptying the dust tank.

WARNING: 

Always wear safety eyewear complying with ANSI Z87.1 (or in Canada CSA Z94.3) 

when using as a blower.

WARNING: 

To avoid injury to bystanders, keep them clear of blowing debris.

CAUTION: 

Wear a dust mask if blowing creates dust which might be inhaled.

CAUTION: 

To reduce the risk of hearing damage, wear ear protectors when using the vac/blower

for extended hours or when using it in a noisy area.

1.   Remove reusable filter and replace it with foam filter when you do wet pickups.

2.   This wet/dry vac is equipped with a float mechanism which will rise automatically to cut off the 

airflow when the liquid in the tank reaches a predetermined level. When this happens, turn off vac, 

unplug the power cord, and empty the dust tank. You will know that the float has shut the airflow off 

because the suction ceases and the motor noise becomes higher in pitch due to increased motor 

speed. The liquid capacity may vary with the rate of pickup.

IMPORTANT: 

                        1. To reduce the risk of damage to the vac, do not run motor with float in raised position.

2. Wet pick up accessories should be washed periodically after picking up wet, sticky kitchen 

accident. This can be accomplished with a warm solution of soap and water. 

OPERATING INSTRUCTIONS

7

Foam filter

Float in raised position 

1.   Remove the power head assembly of the wet/dry vac by pulling outward on the lid clips located 

      on each side of the vac. Lift off the power head assembly.

2.   Dump the tank contents into the proper waste disposal container.

Summary of Contents for 8210413B












Reviews: