Standard Horizon HX751 Owner'S Manual Download Page 20

Page: 20 / 56

HX751

Page 20

5.2 INDICATORS

Information Bar
The temperature or battery voltage is shown here.

Indicators

“

” indicates High power (5 Watts); “

” indicates Medium power (2.5

Watts); and “

” is for Low power (1 Watt). “Blank” in this location indicates

Normal power (6 Watts).

VOL

Indicator

This indicator shows the receiver audio volume level.

SQL

Indicator

This indicator shows the squelch level.

“

SCN

” Indicator

This indicator appears when the Scan is activated.

“

” Indicator

This indicator appears when the Dual Watch is activated.

“

DUP

” Indicator

This indicator appears when the Duplex Channel is selected.

“

” Indicator

This indicator shows the channel is in the “Priority Channel”.

USA/INTL/CAN

Indicator

These indicators show the “band” of operation for the particular channel.
“

USA

” indicates the USA band; “

INTL

” indicates the International band;

and “

CAN

” indicates the Canadian band.

Summary of Contents for HX751

























































Search results

Summary of Contents for HX751

Reviews:

Related manuals for HX751

Brands by name

Popular brands

Standard Horizon HX751, Owner'S Manual

Search results

Summary of Contents for HX751

Reviews:

Related manuals for HX751

Brands by name

Popular brands