Stairmaster StepMill SM5 Technical Manual Download

Page: 27 / 30

Contact Heart Rate Testing - Gauntlet

Contact heart rate is not

working on the Gauntlet.

Make sure there are no loose

connections in the contact

heart rate system.

Check

Connections

Are the cables

connected?

Yes

Connect the

cables and test the

contact heart rate.

Is the heart

rate working?

Heart rate is

operational.

Yes

Verify that the

heart rate cables
are connected to

the heart rate

plates.

Perform a
Continuity

Check on

Cables and

Plates.

All cables have

continuity?

Reconnect all

cables and test

contact heart rate.

Is the heart

rate working?

It is possible that

the cable is not

connected to the

plate.

Check

Connections

at the Heart
Rate Plates

All cables have

continuity?

Yes

Replace the contact heart

rate cable (PN: 050-0324)

Yes

There may be a

short in the

system.

Ensure there

are no shorts

in the system.

Are there any

shorts?

Replace the

console

Yes

Last revised 10/5/15

Summary of Contents for StepMill SM5































Search results

Summary of Contents for StepMill SM5

Reviews:

Related manuals for StepMill SM5

Brands by name

Popular brands

Stairmaster StepMill SM5, Technical Manual

Search results

Summary of Contents for StepMill SM5

Reviews:

Related manuals for StepMill SM5

Brands by name

Popular brands