Stac SS500P Installation Manual Download Page 15

The THERMAFLOW 500P Hydraulic Cooler & Tank Stabilizer is warranted against 
any defect in material and workmanship which existed at the time of sale by STAC, 
Inc. according to the following provisions, subject to the requirements that the Cooler 
must be used only in accordance with the catalogue and package instructions.

The Cooler is warranted for a period of TWO Years from the date of installation. If 
during the warranty period the cooler fails to operate to STAC’s specifications due 
to a defect in any part in material or workmanship that existed at the time of sale by 
STAC, Inc., the defective part will be repaired or replaced, at STAC, Inc.’s discretion, 
at no charge, if the defective part is returned to STAC, Inc. with transportation 
prepaid.

The above warranty shall terminate if any alterations or repairs are made to the 
System other than at an authorized dealer or if the cooler is used on any equipment 
other than the equipment upon which it is first installed.

THE FORGOING WARRANTIES ARE IN LIEU OF ALL OTHER OBLIGATIONS 
AND LIABILITIES, INCLUDING NEGLIGENCE AND ALL WARRANTIES OF 
MERCHANTABILITY AND SUITABILITY, EXPRESSED OR IMPLIED AND STATE 
STAC, INC.’S ENTIRE AND EXCLUSIVE LIABILITY AND BUYER’S EXCLUSIVE 
REMEDY FOR ANY CLAIM OF DAMAGES IN CONNECTION WITH THE SALE, 
REPAIR OR REPLACEMENT OF THE ABOVE GOODS, THEIR DESIGN, 
INSTALLATION OR OPERATION.  STAC, INC. WILL IN NO EVENT BE LIABLE 
FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL 
DAMAGES WHATSOEVER, AND OUR LIABILITY UNDER NO CIRCUMSTANCES 
WILL EXCEED THE CONTRACT PRICE FOR THE GOODS FOR WHICH 
LIABILITY IS CLAIMED.

60 West Sycamore Street • St. Paul, MN  55117

800-334-7699 • 763-235-7822 Fax

Web: www.thermaflow.com

Inc.

THERMAFLOW WARRANTY

Thermaflow is a registered trademark of STAC, Inc.  All Rights Reserved. 

 

Form 500901  Rev: 04/18

®

Summary of Contents for SS500P
















Reviews: