background image

3

READ AND FOLLOW SAFETY 
INSTRUCTIONS!

This is the safety alert symbol. When you see this symbol on your system

or in this manual, look for one of the following signal words and be alert

to the potential for personal injury.

warns about hazards that 

will

cause death, serious personal in-

jury, or major property damage if ignored.

warns about hazards that 

can

cause death, serious personal in-

jury, or major property damage if ignored.

warns about hazards that 

will

or 

can

cause minor personal injury

or property damage if ignored.

NOTICE 

indicates special instructions not related to hazards.

Carefully read and follow all safety instructions in this manual and on equip-
ment. 

Keep safety labels in good condition; replace if missing or damaged.

Incorrectly installed or tested equipment may fail, causing
severe injury or property damage. 

Read and follow instructions in owner's manual when installing
and operating equipment. Have a trained pool professional per-

form all pressure tests.
1. Do not connect system to a high pressure or city water system.
2. Use equipment only in a pool or spa installation.
3. Trapped air in system can cause explosion. BE SURE all air is out of system

before operating or testing equipment.

Before pressure testing, make the following safety checks:

• Check all clamps, bolts, lids, and system accessories before testing.
• Release all air in system before testing.
• Tighten Sta-Rite trap lids to 30 ft. lbs. (4.1 kg-cm) torque for testing.

Water pressure for test must be less than 25 PSI (172 kPa).

• Water Temperature for test must be less than 100

o

F. (38

o

C).

• Limit test to 24 hours. After test, visually check system to be sure it is ready

for operation. Remove trap lid and retighten hand tight only.

NOTICE:

These parameters apply to Sta-Rite equipment only. For 

non-Sta-Rite equipment, consult manufacturer.

IMPORTANT

SAFETY 

INSTRUCTIONS

Always follow basic safety pre-
cautions with this equipment, in-
cluding the following.

To reduce the risk of

injury, do not permit children to
use this product unless they are
closely supervised at all times.

This pump is  for

use with permanently installed
pools and may also be used with
hot tubs and spas if so marked.
Do not use with storable pools. A
permanently installed pool is con-
structed in or on the ground or in
a building such that it cannot be
readily disassembled for storage.
A storable pool is constructed so
that it may be readily disassem-
bled for storage and reassembled
to its original integrity.

SAVE THESE 

INSTRUCTIONS

Summary of Contents for JTACL













Reviews: