background image

Technical Information

Maximum Ratings:

                                               3450RPM, P1 1375W, P2 1100W, 10.0A

IP Rating:

IP25

Inlet (Suction):

ABS Barrel Union to suit 50mm PVC pressure pipe

to AS/NZS 1477

Outlet (Discharge):

ABS Barrel Union to suit 50mm PVC pressure  pipe

to AS/NZS 1477

Max Working Pressure:

260 kPa

Water Temperature Range:

5°C – 40°C

Maximum Ambient temperature:  

5 5°C

Recommended pH Range:

7.2 - 7.8 (Guide Only)

Sound Power Level (Lwa):

Motor:

            

Radial flux, permanent magnet, DC

Protection: 

Mains over voltage, mains under voltage, over temperature,

                     under temperature, locked rotor, over current, phase disconnect.

Supply cord: 

10A, H07RNF, 2m.

Low:         69dB

                                                Med:         63dB
                                                High:        57dB

Override:  73dB

?

4

RPM:

Step1

2600RPM (4 hours) default factory setting

Step2

2100RPM (4 hours) default factory setting

Step3

1600RPM (4 hours) default factory setting

Override / Adjustable Range:

600-3450RPM (2 hours)

Rated Current:

Step1 

5.4A (max)

                

Step2 

3.2A (max)

               

Step3 

1.7A (max)

Override:

10.0A

Input Power (P1):

Step1

690W (max)

                                                                Step2

375W (max)

                                                                Step3

180W (max)

Override:

1375W (max)

Pump Power (P2):

Step1

550W (max)

                                                                Step2

300W (max)

                                                                Step3

145W (max)

Override:

1100W (max)

Model:

  

enviroFLO 1100

Electrical Rating:

230-240V 50Hz single phase

1

1

0

0

enviro

MAX

L300241_EnviroMAX_OM

Monday, 11 August 2014 10:18:34 AM

Summary of Contents for enviroMAX





















Reviews: