manualshive.com logo in svg

ST ST102, Operation And Maintenance Instructions, Page: 24 / 43

Share
Download
ST ST102 Operation And Maintenance Instructions Download Page 24

19

 CONTROL VALVE

 CONTROL VALVE

PRESSURE GAUGE REPLACEMENT 

0

1

2

3

4

6

5

kg/c m

2

Pressure  gauge  regulator  act  as  the 

display  that  indicates  the  current 

pressure of the pump.

1. Identify whether the pressure gauge is

broken.

2. Using the correct size of spanner, unscrew 

the pressure gauge away from the  

Control Valve.

3. Replace with the new pressure gauge and 

screw it into the Control Valve using the 

suitable spanner.

Single Lever Control Unit 

Fluid  is  directed  to  the  boom  lines  or  other 

spraying  devices  by  four  outlet  valves  which 

may be operated individually or as a group. The 

individual valves are open when levers “C” are 

vertically  down  and  closed  when  vertically  up. 

Raising the single lever ”D” and swinging it over 

to the other side of the valve opens the flow to 

all valves and swinging it back closes the flow.

Once  the  required  outlets  have  been  selected 

using  the  individual  valves,  spraying  may  be 

started and stopped by using the single lever. If 

you wish to stop spraying but leave the tractor 

PTO running, close the single lever and move 

the bypass lever to by-pass mode.

22

ST102 - 300L/400L/600L/800L/1000L

- Tractor Mounted

Summary of Contents for ST102












































Reviews:

No comments