ST ST102 Operation And Maintenance Instructions Download Page 13 | Manualshive

Page: 13 / 43

background image

11

TECHNICAL DATA

Sprayers dimensions and weight

On the identification plate, the full-load weight of the machine is indicated, measured

WITHOUT the distribution device, and WITHOUT the accessories possibly installed.

In order to calculate the weight on the hoister in operative conditions (at full load), add to

the weight indicated on the identification plate, the weight of the installed accessories, the

weight of the distribution device which is used, and the 50% of the weight of the used

cardan shaft

TOTAL WEIGHT

+ SPRAYHEAD WEIGHT

+ ACCESSORIES WEIGHT

+ 50% CARDAN SHAFT WEIGHT

= WEIGHT ON THE TRACTOR

THREE-POINT HOISTER

TECHNICAL OUTER DIMENSION

in mm

A(mm) X B(mm) X C(mm)

ST102 - 300L : 1280mm X 1067mm X 1380mm

ST102 - 400L / 600L : 1280mm X 1303mm X 1723mm

ST102 - 800L / 1000L : 1280mm X 1295mm X 1588mm

.

.

ST102 - 300L/400L/600L/800L/1000L

- Tractor Mounted

B

C

A

«
...
11
12
13
14
15
...
»

Summary of Contents for ST102












































Reviews:

No comments

Related manuals for ST102

Brand: DEMA Pages: 3

ProSpray 3.21 0558019

Brand: WAGNER Pages: 28

Brand: SAMES KREMLIN Pages: 5

Corona Cup Gun Ki

Brand: Nordson Pages: 4

IND-MD-DF-ESF-R2-SP0017

Brand: Larson Electronics Pages: 2

Brand: Fast Pages: 87

Larius GHIBLI SE 9000

Brand: Samoa Pages: 38

Brand: Raider Pages: 80

Brand: Spectrum Pages: 20

Brand: Graco Pages: 8

Brand: Graco Pages: 34

Brand: DeVilbiss Pages: 8

Brand: ASM Pages: 40

Brand: sunjoe Pages: 20

SaniSpray HP ProPack 25T781

Brand: Graco Pages: 16

Brand: Tritech Pages: 60

COILSHOT SC-CS-100

Brand: SpeedClean Pages: 8

MARRO TWIN FORCE 1000

Brand: Hardi Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands