manualshive.com logo in svg

SST Automation GT200-3HT-MT, User Manual, Page: 29 / 46

Share
Download
SST Automation GT200-3HT-MT User Manual Download Page 29

User Manual

3-channel HART/Modbus TCP Gateway

GT200-3HT-MT

WWW.SSTCOMM.COM

29

4.2.3 Conflict Detection

Conflict detection is used to check the distribution condition of the input and output data of all commands stored in

the memory.

Click

icon will show the conflict detection interface as follow:

The left side is configuration commands, the right side is data memory address including receive data storage

address and send data storage. Upper side is memory distribution of the HART’s sending data; lower side is memory

distribution of the HART’s receiving data. When one memory unit is configured with two commands or more, the

memory unit will display red color. When the distributed memory exceeds the defined scale of gateway, the exceeding

part will display yellow color. White color area shows the usable memory. Green color area indicates occupied memory.

Clicking one command, the distribution chart shown in blue will show the storage location of input/output data.

4.2.4 AutoMap

Automap will automatically distribute the memory with no confliction according to the input/output bytes

Summary of Contents for GT200-3HT-MT















































Reviews:

No comments