Spyder Electra with Eye TADAO EDITION, User Manual

Page: 9 / 15

13 14
To INCREASE your velocity fps using the Allen wrench, turn the Velocity Adjuster / Spring Guide clockwise.
To DECREASE your velocity fps using the Allen wrench, turn the Velocity Adjuster / Spring Guide counter-
clockwise. NOTE: Allen wrench provided in the spare parts kit. NOTE: Velocity Adjuster / Spring Guide doesn’t
remove from the rear of the Sticker Plug.
NOTE: The velocity of this paintball marker ranges from approximately 240 – 300 feet per second (fps). Velocities
will fluctuate or vary due to paintball size, climate condition, altitude, type of air source and variance in spring
tension from manufacturing.
WARNING
• The recommended Velocity speed should be no greater then 300 fps. Not doing so can cause serious injury or death
if the velocity is set dangerously high.
• Paintball markers are not intended to shoot any person less then 25 feet without eye/face protection.
• Never point a loaded marker at any person who is not wearing the proper face protection.
• Never at any point should you look down the barrel, whether the marker is loaded or not.
• Using a paintball marker outside a non designated paintball field can be illegal, and is subject to law
enforcement penalties if property damage is caused by the user.
C/A ON/OFF ADAPTER
HELPFUL TIP: Make sure to have the C02 / Compressed Air Tank filled before use.
• Firmly, hand tighten the CO2 / Compressed Air Tank clockwise into the markers C/A On/Off
adapter.
• Tighten the tank clockwise in the markers C/A On/Off adapter until it is snug. If an air leak occurs
between the tank and the C/A On/Off adapter, replace the urethane o-ring.
• To pressurize the marker turn the adapter knob towards the ON position to pierce the pin valve on
the tank.
• To release the pressure turn the dial knob towards the OFF position. This will release the pressure
in the hose line and stop the air flow in the marker.
IMPORTANT: Markers that are equipped with regulators may store residual air after the C02/
Compressed Air Tank has been removed. To fully remove any residual air stored in the marker, turn the
C/A On/Off adapter knob counter-clockwise to shut off the air supplied from the tank. Take several dry
fire shots with the marker pointed in a safe direction until the marker has no remaining air.
IMPORTANT: You should never need to use any hand tool to attach a Compressed Air Tank to the C/A
On/Off adapter.
NOTE: O-rings in the markers parts kit are not supplied to attach with a C02/ Compressed Air Tank.
NOTE: The hose line adapter supplied on the C/A On/Off is American thread 1/8” (NPT).
C/A ON/OFF Adapter
REGULATOR ADJUSTMENT
WARNING: Never at any time should you attempt to unscrew the Vertical Regulator while the marker is
pressurized. Doing so can cause serious injury or death.
The Electra w/Eye is equipped with the Fast Charge Inline Regulator that improves the markers
velocity consistency and air efficiency. Once the C02/ Compressed Air tank has been installed and
tank valve is opened by turning the C/A On/Off adapter knob clockwise, the marker is potentially
capable and ready to fire.
Adjustment to the regulator output pressure is done through the regulator adjuster knob located at the
bottom of the regulator with the use of the wrench provided with the spare parts kit.
STEP 1
Loosen the Regulator Adjuster Lock Screw located on the on the Regulator Adjuster Knob.
STEP 2
Using the Open End Wrench provided with the spare parts kit, turning the adjuster knob
clockwise will decrease the regulator output pressure and turning the adjuster knob counter clockwise
will increase the output pressure of the regulator. The regulator output should be no less than 300psi
or at least one and a half turn counter clockwise of the Regulator Adjuster Knob from the bottom of
the regulator.
NOTE: Too low of an output setting from the regulator will result in very low velocity and some re-
cocking issue with the marker. You must have adequate output air pressure from the regulator to avoid
starving the marker for air. Too high of an output setting of the regulator will result in excessive air
consumption and poor air efficiency. This may also result in dangerously high velocities exceeding the
recommended safety limits for playing paintball.
STEP 3 After each adjustment to the regulator, you must fire the marker a few times to let the
regulator settle to its new output setting.
STEP 4 Securing the Regulator Adjuster Lock Screw will prevent the adjuster knob from turning due
to vibrations keeping the regulator output setting stable and locked.
IMPORTANT: Any adjustment to the inline regulator output pressure will affect the markers velocity
setting, always chronograph the marker after each adjustment. NOTE: The Fast Charge Inline
Regulator is tuned from the factory to have an output pressure of approximately 350 psi.
When adjusting the Regulator to “Decrease” the output pressure, you will need to fire the marker a
few times to get the new setting.
IMPORTANT: (Make sure you have your marker pointed in a safe
direction and you are following all safety guidelines set with the use of this product.)
IMPORTANT: Markers that are equipped with regulators may store residual air after the Compressed
Air Tank has been removed. To fully remove any residual air stored in the marker, turn the C/A On/Off
adapter knob counter-clockwise to shut off the air supplied from the tank.
IMPORTANT: Do not attempt to service the regulator unless you have received proper training from a
qualified Kingman Group service technician. Doing so will VOID all regulator warranties and liabilities
from Kingman Group. If you experience any leaks or problem with the regulator, contact Kingman Group
Technical Support Service Department.
IMPORTANT: Always remove all paintballs and C02 / Compressed Air Tank from your marker and
remember to keep the marker in its un-cocked position before placing it in storage.
SCR026
REG012
English