Spyder Electra with Eye TADAO EDITION, User Manual

Page: 7 / 15

9 10
BATTERY INSTALLATION
BATTERY INSTALLATION
Kingman Group recommends using a Spyder 9.6volt NiMH Rechargeable Battery as a power source for optimum
performance and will provide a superior shot count of around 5000 to 6000 rounds. (Spyder Battery and Charger
Sold Separately)
NOTE: This marker is compatible with the use of 9volt Alkaline batteries. Use only premium brand Alkaline batteries
for best performance. (Battery Not Included)
Shot counts will vary depending on the type of 9volt Alkaline battery used (2300 to 3200), choosing a premium
brand battery will give the best results.
IMPORTANT: Performance will vary depending on the mode used and rate of fire achieved.
STEP 1 Remove the three M4x 8 Screws from the Right side grip panel. NOTE: Allen wrench provided in
the spare parts kit.
STEP 2 Attach the battery to the battery harness.
STEP 3
Re-tighten the three M 4x8 Screws.
HELPFUL TIP: Please note how the parts are removed for easy reassembly.
CHARGING INSTRUCTIONS
Spyder 9.6volt Battery (US LED) optional accessory
To charge a Spyder 9.6 NiMH battery, the circuit board must be in the OFF position. Spyder batteries (JE1015) are not
fully charged when purchased. Using the supplied Spyder LED A/C Charger (JE1029), plug the charger into the charger
port located at the rear of the trigger frame. For a complete charge, Kingman recommends a charging time of
6-8 hours.
STEP 1 Plug the Spyder LED A/C charger into a power outlet.
STEP 2
Connect the Spyder A/C charger cord to the rear of the markers trigger frame’s charging port..
STEP 3 The LED indicator on the Spyder LED A/C charger will display RED when the battery is charging.
STEP 4 The LED indicator on the Spyder LED A/C charger will display GREEN when the battery is fully charged.
STEP 5 Unplug the Spyder LED A/C charger cord from the rear of the markers trigger frame’s charging port
after charging.
STEP 6
Remove the Spyder LED A/C charger from the power outlet.
IMPORTANT: Never charge the battery for over 24 hours, as you will risk damaging the battery and/or electronics.
HELPFUL TIP: It is recommended that the battery be charged prior to use in order to ensure maximum performance,
especially if the battery has not been used in over a week. NOTE: A fully charged Spyder battery will last about
5000-6000 shots, depending on your firing methods or firing mode in use. Under normal use and charging
conditions the expected life of the Spyder battery is approximately 700-1000 charging cycles.
To avoid any risks of having the Battery explode or the Circuit Board burned: charge only Spyder 9.6volt NiMH
Batteries in Spyder electronic frames.
IMPORTANT
• DO NOT attempt to recharge any Alkaline or any other type of battery in the Spyder electronic frame.
• DO NOT try to recharge batteries that are rusted, corroded, damaged or leaking.
• FAILURE to follow any of the instructions will VOID ALL WARRANTIES AND LIABILTIES from Kingman.
Kingman will not be held liable for any injury or damages from the improper use of this product. This accessory is not
intended for use with any other product other than what Kingman designed it for.
Spyder 9.6volt Battery (EU) optional accessory
To charge a Spyder 9.6 NiMH battery, the circuit board must be in the OFF position. Spyder batteries (JE1015) are
not fully charged when purchased. Using the supplied A/C Charger (JE1025), plug the charger into the charger port
located at the rear of the trigger frame. For a complete charge, Kingman recommends a charging time of
6-8 hours .
IMPORTANT: Never charge the battery for over 24 hours, as you will risk damaging the battery and/or electronics.
HELPFUL TIP: It is recommended that the battery be charged prior to use in order to ensure maximum performance,
especially if the battery has not been used in over a week.
NOTE: A fully charged Spyder battery will last about 5000-6000 shots, depending on your firing methods or firing
mode in use. Under normal use and charging conditions the expected life of the Spyder battery is approximately
700-1000 charging cycles.
To avoid any risks of having the Battery explode or the Circuit Board burned: charge only Spyder 9.6volt NiMH
Batteries in Spyder electronic frames.
IMPORTANT
• DO NOT attempt to recharge any Alkaline or any other type of battery in the Spyder electronic frame.
• DO NOT try to recharge batteries that are rusted, corroded, damaged or leaking.
• FAILURE to follow any of the instructions will VOID ALL WARRANTIES AND LIABILTIES from Kingman.
Kingman will not be held liable for any injury or damages from the improper use of this product. This accessory is not
intended for use with any other product other than what Kingman designed it for.
English
GRP005
SCR002
SCR002
WRH002
Part Names and Numbers described in this section:
Dual Texture Grip Panel (#GRP005)
M4 x 8 Screw (A) (#SCR002)
Battery Harness (#WRH002)