background image

11

9.  

Service Instructions

9.3

Installation of seals and assembly of valve

Provide all seals with a thin layer of grease before their 
installation.

a.

Insert the guide bush 

(7) 

and o-ring

(6)

into the yoke

(8)

Fasten the yoke

(8) 

at the actuator 

(13).

b.

Install the seat seal

(2) 

in the lower valve shaft

(3)

.

(see Service Instructions 11.)

c.

Insert the o-rings 

(4, 5)

into the shaft grooves.

d.

Slide the protective pipe over the thread of the guid rod.
Place the shaft with bellow unit

(3) 

and guide rod

(9) 

through 

the yoke

(8) 

and actuator 

(13).

-

The shaft must be led smoothly through the guide bush in 
the yoke. If the shaft stiffs, check the right fit of the guide 
bush.

e. CU design and valve position indicator:

Place the centering washer

(16)

. Apply a drop of a screw locker

(e.g. type: Loctite - semi-solid) on the thread of the guide rod.
Screw on the hexagon nut

(21) 

and fasten it with a

tightening torque of MD = 40 Nm. 

Hold up the centering 

washer during this process.

-

CU:

Tighten the plastic actuator screw.

-

Valve position
indicator:

Screw on the metal actuator screw and 
fasten it with a tightening torque of 

Md = 40 Nm. 

actuator screw

hex. nut

centering washer

cu adapter

guide rod

actuator

yoke

housing

guide bush

o-ring (6)

o-ring (4)

o-ring (5)

seat seal

shaft with 

bellow unit

control unit

UK

DELTA MF4-UK0.qxd / 12.2004

Membrane Valve with Bellow Unit

DELTA MF4

Operating Manual rev. 0

Summary of Contents for APV DELTA MF4




































Reviews: