Sports Attack STRIKE ATTACK Instruction Manual Download Page 4

STRIKE ATTACK™ SOCCER MACHINE

SPORTS ATTACK, LLC 

 800-717-4251 

 sportsattack.com

2

Safety Instructions 

SAFETY INSTRUCTIONS

AC Model - ELECTRICAL SAFETY

Use a 115 volt single phase 3-wire grounded power source.
Up to 200 ft. from power source, use a minimum #14/3 grounded 3-wire extension cord.
Over 200 ft. from power source, consult a licensed electrician for required power cord size.

DC Model - BATTERY SAFETY 

Keep away from open flame
 Electrical  Hazard
Unplug charger before removing cables 

OPERATING SAFETY

CAUTION:

 Never reach down near moving throwing wheels for any reason! If it is  

necessary to reach into the throwing wheels, 

ALWAYS

:

  1. Turn speed dials to “0” and turn off the machine.
  2. Unplug Strike Attack from power source.
  3. Wait until the throwing wheels have come to a complete stop before reaching hands  

    or fingers anywhere near the throwing wheels. 

CAUTION: 

Carefully check Strike Attack for completeness and condition before  

connecting to electrical power:
Carefully check the throwing wheels frequently for cleanliness, chips and cracks. Do not 

use the machine if the throwing wheels are damaged, or if chips or cracks appear in the 

wheels. (For damage within Warranty period, see Warranty Statement, page xi.)

ALWAYS 

set the speed control to “0” before connecting the machine to power.  

Check that the speed control is at “0” before turning the throwing wheels “ON”.
Do not allow anyone to walk in front of the Strike Attack if it is connected to electrical power.
Do not allow anyone to walk in front of the Strike Attack if it is on.

CAUTION

:

 DO NOT

 plug in or energize this equipment until all assembly instructions  

and operation instructions are read and followed.

BALL SELECTION

Balls must be official size and consistent in type to produce repeatability. Smaller balls 

(usually used with youth players) can be used without adjustment. Air pressure is  

important! Under pressurized balls will not throw as far. Air pressure should be checked  

on a regular schedule for consistent performance.
Smaller youth balls will work well for younger players. However, distance and speed will  

be reduced.
Wet balls may not throw accurately. 
See Wheel Cleaning Instructions on page 10.

WARNING

Carefully read all instructions in 

this manual, and all labels and 

warnings on Strike Attack Soccer 

Machine before using.
Use machine only under adult  

supervision. Failure to operate  

Strike Attack as described in  

this manual can result in severe  

personal injury or death.

• 

Strike Attack AC Soccer Machine 

must be connected to a properly 

grounded electrical receptacle.

• 

Do not operate on wet ground.

CAUTION

Keep hands away from throwing 

wheels anytime the machine is  

connected to a power source.

• 

Carefully check Strike Attack for 

completeness and condition 

before connecting to electrical 

power.

Summary of Contents for STRIKE ATTACK


















Reviews: