background image

 

 

 

  08/2005  

510200020-510230020                                                                

 

        

4/26

 

Pneumatic Chain Saw  5 1020/5 1021/5 1022/5 1023

 

 
 

FOR YOUR SAFETY 

 
Do wear provisioning clothing and outwear! 
 
 

 

 
The clothing has to be purposing and shall not hinder. 

 

 

Wear tight clothes with insert-combined suit, no working suit

 
 
 
 
There  should  be  no  clothing,  no  scarf,  no  tie,  no  jeweils  –  that  can  possibly  get  into  wood  or 
undergrowth. Take care of long hair (hair-net)! 
 
 
 

 

Wear safety boots with maximal grip and steel cap! 

 
 
 
 

 

Use a hard hat if parts could fall down! 

 

 

Do also use goggles! 

 
 
 
 
Use „personal“ hear protection! Like ear-flaps. 
 
 
 

 

Wear tight and non-slip gloves! 

 

 

Made of chromium leather 

 
 
 
Transporting the motor saw 
Only if the air supply is separated. 
Always attach chain guard – even for transport over a short distance. 
 
Carry the saw only at the pipe handle 
Guide (bar) should face to the back! 
 
Transporting in vehicles: 
Protect the saw so that it cannot fall to the side and get damaged. If the motor saw is not in use 
it should be put to the side so that there is no risk for anybody. 
 
 
 
 
 
 

Summary of Contents for 5 1020 0020



























Reviews: