background image

3 - Setting Up Your Machine

3.6 - Attaching the Paper Side Stops

Page 08

3.6.1

Diagram 3-30

Attach the Paper Side Stops (FM4-4006) using two (2) Side Stop 

Screws (FM4-4007) each.  Position the Paper Side Stop as de-

sired and tighten down with light pressure.   

3.7 - Attaching the Chip Bag

3.7.1

Diagram 3-50

Attach the Chip Bag (FMM6-652A) to the machine by stretching 

the mouth of the bag over the Master Chip Chute and hooking 

the aluminum bar onto the bracket located on the top flat portion 

of the master chip chute as shown.  Please note that you must 

empty this bag as needed to avoid clogging.

Master Chip Chute

Chip Bag

Table

Paper Side Stop

Side Stop Screws

3.8 - Electrical Instructions

3.8.1

3.8.2

Your FMMH-3.1 comes with an electrical cord containing the plug 

to fit into standard grounded 115V outlets.  This machine has a 

combined full load draw of 18.8 Amps and requires a 20 Amp 

Circuit.

Making sure that nothing is interfering with the drill bits, plug the 

cord set into a grounded 115V outlet.  To turn the Drill Motor on, 

face the machine and press the Rocker Switch on the left-hand 

side labeled “Drill Motor.”  To turn the Table Motor on, face the ma-

chine and press the Rocker Switch on the right-hand side labeled 

“Table Motor.” 

Diagram 3-60

Rocker Switch

(Drill Motor)

Rocker Switch

(Table Motor)

Summary of Contents for FMMH 3.1

























Reviews: