background image

6 - Trouble Shooting Guide

6.1 - Determining the Cause and Correction to Certain Problems

Page 18

Problem

Cause

Correction

Machine vibrates, wobbles, 

resonates, etc.

The machine is not level on the 

floor.

Use the leveling feet to make the 

machine level on the floor.  See 

Setting Up Your Machine

The drill bit(s) are drilling into 

the drill strip or they are not 

drilling through the bottom 

sheet of the product you are 

drilling.

Drill bit(s) are not adjusted 

properly to the card stock/card 

stock not used.

Adjust your drill bit(s) per 

Operat-

ing Instructions

.

The outside Heads are 

difficult to adjust.

The Lead Screw and/or Traverse 

Rods are dry or damaged.

Lubricate per 

Maintenance

 

schedule.  Check for damaged or 

worn components.

The drill bit(s) do not rotate 

when the motor is turned on.

A Drive Belt is broken on the 

Flexible Drive System.

Replace the broken belt.  See 

Maintenance

.

A Drive Belt is loose on the 

Flexible Drive System.

Tighten the loose belt.  See 

Maintenance

.

An Insert Retainer Screw is 

hitting the inside of the Chuck 

Housing. 

Adjust the Chuck and tighten the 

Insert Retainer Screw.

The Hand Wheel Lock is tightend 

down in place.

Loosen the Hand Wheel Lock 

enough so the Hand Wheel can 

be turned.

An obstruction is between the 

traversing heads.

Check and remove the obstruc-

tion.

The Chuck(s) were not tightened 

after adjustment.

Re-adjust and tighten.

The machine is located directly 

on a concrete floor.

Place a rubber mat or carpet 

under the machine. 

Drill bit(s) are not concentric.

Re-install drill bit(s) until they are 

concentric.  See 

Operating 

Instructions. 

Summary of Contents for FMMH 3.1

























Reviews: