background image

10

9

Use the chart below as a guide to reading DC 
voltage measurements:

DC V        Read              

range      following

setting        scale

10             0-10

50             0-50

150           0-150          
300           0-300

4.1 Household Batteries

Set the function/range switch to 10V DC to
test household 1.5 volt through 9 volt batteries.
Touch the red (+) test lead to the (+) terminal
and the black (-) test lead to the (-) terminal
of the battery. Read the 0-10 scale to 
determine the condition of the battery.

5. DC Milliamp Measurement

1) Fully seat the test leads in the correct input

jacks, (-) black lead, (+) red lead.

2) Set the function/range switch to the 

appropriate DCmA setting.

3) Touch the test leads to the circuit in series (in

line with the circuit) so that the circuit current
passes through the multimeter in order to
make the measurement. If the needle indicator
deflects to the left, reverse the test leads.

DC mA

Read        and

range      following

multiply

setting        scale

reading by:

0.5            0-50         0.01
50             0-50

1

150           0-150      

1

Common DC Milliamperage

Measurements

It is important to point out that milliamps can
also be expressed as thousandths of an
Ampere; therefore 150 milliamps is 150 
thousandths of one Amp. The 150mA function
of your multimeter is commonly used by 
electronics repair technicians and hobbyists to
troubleshoot various low voltage circuits.
Although not normally used for electrical 
troubleshooting around the home, this function
can be used to measure the milliamperage
draw of household items such as flashlights,
and other battery operated devices that do not
draw more than 150 mA. In fig. 2 the red (+)
test lead is hooked up to the (+) terminal of the
lantern battery while the black (-) test lead is
hooked up to the bulb. The meter will indicate
the milliamperage draw when the flashlight
switch is thrown in the ON position.

Do not apply voltage to the

test leads while the meter is set in the 

milliamp range. See #8 

For Your Safety.

6. AC Voltage Measurement

1) Fully seat the test leads in the correct input

jacks (-) black lead, (+) red lead.

2) Set the function/range switch to the 

Figure 2

!

WARNING

HSP5 3-09 manual.qxp  5/8/09  9:57 AM  Page 10

Summary of Contents for GMT-312










Reviews: