background image

10

11

PC CONNECTION

System Requirements

Windows NT 4.0/ NT2000/ XP/ VISTA

Minimum Hardware Requirements

PC or Notebook with Pentium 90 MHz or higher, 32 MB RAM; At least 

50 MB hard disk space available to install the software. Recommended 

resolution of 800 x 600. 

Installing the Software
Note…

 

Different computer systems may require slightly different installation steps 

than those below. 

1.  The first most important step in software installation is to verify that 

the target system meets the general hardware requirements of the 

application. Beginning the installation in a computer machine which 

does not possess the minimum requirements can lead to either an 

unsuccessful installation or failure of the program to run after installing it.

2.  Since programs in general are written to be Operating System 

dependent, make sure that the version of the application you are installing 

corresponds to the Operating System platform running on your machine.

3.  Aside from the general hardware requirements, some computer programs 

also have software requirements prior to installation. Double check if you 

need to update or upgrade your Operating System or if there is a need to 

download other tools or utilities.

4.  Once all the initial requirements have been met, make sure that there 

are no unnecessary programs running before beginning the installation 

procedure. In some instances, applications may require that the antivirus 

programs be disabled. Make sure that you are installing a legitimate 

application before disabling your protection software.

5.  Software installation can be done either from the Internet (skip to step 

8) or from an installation disc provided by the software manufacturer. 

To install from the disc, simply open the CD or DVD drive and insert 

the installer.

6.  A setup wizard window should be launched. In case there is none, open 

the Explorer and navigate to the optical drive. Double click on either the 

Autorun or Setup file.

Summary of Contents for 850013

















Reviews: