Spektrum NX6 Instruction Manual Download

Page: 52 / 53

SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

This device complies with ISED licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operation of the device.

IC INFORMATION

CAN ICES-3 (B)/NMB-3(B)

SPMR6775 Transmitter

Contains IC: 6157A-PLANO1T

Contains IC: 6157A-WACO1T

Contains IC: 21098-ESPWROOM02

SPMAR6610T Receiver

IC: 6157A-TIARLGTNNG

AMA NATIONAL MODEL AIRCRAFT SAFETY CODE

http://www.modelaircraft.org/files/105.PDF

FAA INFORMATION

Prior to flying, contact your local or regional modeling

organizations for guidance and familiarize yourself with the current

local rules and FAA regulations governing model aviation in your

location.More information about model aviation can be found at

www.modelaircraft.org.

The Federal Aviation Administration can be found online at

www.faa.gov.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other

waste. Instead, it is the user’s responsibility to

dispose of their waste equipment by handing it over

to a designated collections point for the recycling

of waste electrical and electronic equipment. The

separate collection and recycling of your waste equipment at

the time of disposal will help to conserve natural resources and

ensure that it is recycled in a manner that protects human health

and the environment. For more information about where you can

drop off your waste equipment for recycling, please contact your

local city office, your household waste disposal service or where

you purchased the product.

EU Compliance Statement:

Horizon Hobby, LLC hereby declares that this product

is in compliance with the essential requirements and

other relevant provisions of the RED Directive.

A copy of the EU Declaration of Conformity is available online at:

http://www.horizonhobby.com/content/support-render-compliance

NX6 Transmitter
Frequency Band:

2404-2476 MHz

Max EIRP:

18.3dBm

AR6610T Receiver
Frequency Band:

2402-2478 MHz

Max EIRP:

19.96dBm

Summary of Contents for NX6






















































Search results

Summary of Contents for NX6

Reviews:

Related manuals for NX6

Brands by name

Popular brands

Spektrum NX6, Instruction Manual

Search results

Summary of Contents for NX6

Reviews:

Related manuals for NX6

Brands by name

Popular brands