Spektrum NX6 Instruction Manual Download

Page: 51 / 53

SPEKTRUM NX6 • TRANSMITTER INSTRUCTION MANUAL

WARRANTY AND SERVICE CONTACT INFORMATION

Supplier’s Declaration of Conformity

NX6 Transmitter Only – SPMR6775
NX6 Transmitter Only and SPMAR6610T – SPM6775

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that

may cause undesired operation.

CAUTION:

changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note:

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Horizon Hobby, LLC
2904 Research Rd.,
Champaign, IL 61822
Email: [email protected]
Web: HorizonHobby.com

FCC INFORMATION

Country of Purchase

Horizon Hobby

Contact Information

Address

United States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

2904 Research Rd

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

[email protected]

877-504-0233

Sales

[email protected]

800-338-4639

Horizon Technischer Service

[email protected]

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

+49 (0) 4121 2655 100

SPMR6775 NX6 Transmitter

Contains FCC ID: BRWPLANO1T

Contains FCC ID: BRWWACO1T

Contains FCC ID: 2AC7Z-ESPWROOM02

SPMAR6610T Receiver

Contains FCC ID: BRWTIARLGTNNG

Summary of Contents for NX6






















































Search results

Summary of Contents for NX6

Reviews:

Related manuals for NX6

Brands by name

Popular brands

Spektrum NX6, Instruction Manual

Search results

Summary of Contents for NX6

Reviews:

Related manuals for NX6

Brands by name

Popular brands