background image

Speidel’s Master Brewer

 

Page 17 of 26 

 

 

 

 
 

You can find further recipes at 

www.speidel-behaelter.de

 

Decant into a sterilized 30l plastic cask by means of a hopper (refer to 
the  illustration)  or  hose.  Disinfect  the  cask  and  decanting  aids 
beforehand  with  sulphurous  acid.  Do  not  allow  the  residues  on  the 
boiler's bottom to flow out with the wort. 
Add 7g of dry yeast into the wort and seal with fermenting cask with 
the fermenting bung and the sulphurous acid that is poured in above. 
Store  the  container  in  darkness  at  16°C  to  20°C.  The  fermentation 
begins  after  approximately  12  hours.  Do  not  forget:  decant  1.5l  of 
wort into a container or similar receptacle and freeze it (before adding 
the yeast). 

Thaw  out  the  frozen  wort  and  carefully  pour  it  into  the 
fermenting  cask  1  hour  before  the  decanting  [i.e.,  bottling]. 
Use a ladle to skim off the foam that is floating on top. Do not 
move the cask any more. Decant into the bottles with a hose. 
Only  fill  the  bottles  up  to  between  90%  and  95%  of  their 
capacity.  Allow  the  bottles  to  stand  at  the  same  temperature 
for 1 to 2 days and briefly ventilate them daily (only at a high 
overpressure). Then allow the beer to mature at 10°C to 15°C 
for another 3 to 4 weeks. 

The fermenting duration is 3 to 5 days. The fermentation has been 
completed  when  no  fermenting  gases  escape  any  longer.  The 
maturing  bottles  must  have  already  been  prepared  during  the 
fermentation. Sterilize the stirrup bottles in the oven at 130°C  and 
allow them to cool down in the oven. Boil the rubber seals. 

Stir the hot wort vigorously (whirlpool effect) in order to clarify 
the wort. Put the cooling spiral (accessory) into the middle of the 
boiler  immediately  after  the  boiling  ends.  Connect  the  spiral  to 
cold water and begin the cooling. Caution: boiling hot water will 
flow out of the spiral at the beginning. Cool down the beer wort 
to  20°C.  You  must  work  in  sterile  conditions  from  now  on 
because of the risk of infection. Allow the separated cooler sludge 
to  be  deposited  on  the  bottom.  Avoid  vibrations.  Duration  of 
approximately 25 minutes. 

Summary of Contents for Braumeister 47070





























Reviews: