background image

4

ASSEMBLY INSTRUCTIONS

FIGURE 2

TOOLS REQUIRED FOR ASSEMBLY

(1)

Screwdriver

(1)

Pliers

(2)

7/16" Wrenches

(2)

1/2" Wrench

(2)

9/16" Wrenches

1. Remove  the  hardware  pack  and  all  loose  parts

from  the  carton.    Be  sure  the  carton  is  empty
before discarding.

2. Lay out and identify all the parts and hardware as

shown on pages 2 and 3.

3.

Place the latch lock lever through the slot in the draw
bar tongue as shown in figure 1. Assemble the 5/16"
x 3-3/4" hex bolt through the tongue, the lever and
two 5/16" hex nuts (one on each side of the lever).
Assemble the 5/16" hex 

lock

 nut onto the end of the

bolt and 

tighten

 so that the bolt can still rotate freely.

Tighten

 the two 5/16" hex nuts against the sides of

the latch lock lever so that the lever is centered in the
slot. See figure 1.

FIGURE 3

FIGURE 1

5. Assemble the hitch bracket to the drawbar tongue,

using  two 3/8" x 1-1/4" hex bolts, 3/8" lock wash-
ers and 3/8" hex nuts. 

Tighten.

 See figure 3.

6.  Assemble  hitch  pin  to  tongue/  hitch  bracket  and

secure with 1/8" hair cotter pin. See figure 3.

5/16" HEX
NUTS

5/16" HEX
LOCK NUT

5/16" x 3-3/4"
HEX BOLT

DRAWBAR TONGUE

LATCH
LOCK
LEVER

TONGUE

3/8" x 1-1/4"
HEX BOLT

3/8" LOCK
WASHER

3/8" HEX
NUT

HITCH
BRACKET

1/8" HAIR
COTTER
PIN

HITCH PIN

4.

Hook the 

short

 end of the spring into the hole in the

latch lock lever. Use the spring puller tool to hook the

long

  end  of  the  spring  into  the  square  hole  in  the

tongue.  The  spring  puller  tool  can  be  stored  when
finished. See figure 2.

LONG END
OF SPRING 

LATCH LOCK LEVER

SPRING PULLER TOOL

Summary of Contents for Agri-Fab 45-0175













Reviews: