background image

  MAINTENANCE & SAFETY

The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to

replace frayed, kinked, cracked or otherwise damaged hydraulic hoses or hydraulic components.

NEVER 

check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.

Escaping fluid under pressure can have sufficient force to penetrate skin causing SERIOUS INJURY or even DEATH.

Leaks can be safely detected by passing a piece of cardboard over the suspected leak and looking for discoloration.

NEVER 

remove the cap from the hydraulic tank or reservoir while the log splitter is running. The tank could contain hot 

oil under pressure which could result in serious injury. 

NEVER

 adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qualified 

service technician should perform this adjustment.

ALWAYS 

seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or 

reaction can develop if proper medical treatment is not administered immediately.

ALWAYS 

be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and forth

should it become necessary to loosen or remove any hydraulic fitting.

Page 5

 FIRE PREVENTION

NEVER

 operate your log splitter near a flame or spark or smoke during operation. Hydraulic oil and gasoline are 

flammable and can explode.

NEVER 

fill the gas tank while the engine is hot or running. Allow the engine to cool before refueling.

ONLY

 refuel your log splitter in a clear area with no gas fumes or spilled gas.

ALWAYS

 replace the gas cap securely.

If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition until 

the spilled gas has evaporated.

ALWAYS

 drain the fuel tank prior to storage to avoid the potential fire hazard.

ALWAYS

 store gasoline in an approved, tightly sealed container and away from heating appliances. Store the container in 

a cool, dry place. 

Summary of Contents for S401628BB


















Reviews: