background image

5

STEP 

2

Install RO Drain Connector

Drain Connector Installation

Choose the drain outlet location. See Fig. 1 (page 3)

Remove protective cover from back of Foam Seal 

N

.

Knock out center hole and align holes then attach to Drain Connector 

front plate

K

.   

Position the Drain Connector 

K

on the sink drain pipe above the drain trap. Allow room for drilling. Tighten Screws 

L

and 

Nuts

securely.

Use a battery powered or properly grounded drill. Using the Drain Connector 

K

port as a drill guide,  drill a 7/32” hole through 

the wall of the drain pipe. Do NOT penetrate the opposite side of the pipe and be careful not to damage the side of the drain 
port fitting. 

If you wish to install your drain in a remote location refer to page 10.

STEP 

3

Install RO Filter System Assembly

The Reverse Osmosis Filter System Assembly Head 

is mounted on Mounting Screws 

C

.  

The Mounting Screws

allow you to lift the RO Filter System Assembly without any hardware removal. 

Choose an easy-to-access area under the sink to mount the RO Filter System Head

A

NOTE: To allow adequate space for filter changes, allow clearance of 4” - 6”below the filter 

to 

the floor. The Filter 

System Assembly must be mounted in a vertical position.

NOTE: Mount the Filter System Head to a solid cabinet wall or wall. If a solid surface is not available, use hollow-wall 
anchor bolts or toggle bolts (not included) to secure to the wall. 

Using the Built-in Bracket on the back of the RO System Head 

A

, mark the holes for the Mounting Screws 

C

on the 

wall surface.

Using a 1/8" drill bit, drill two pilot holes for the Mounting Screws

C

. Insert Mounting Screws

into the wall with a 

Phillips screwdriver, leaving approximately 3/8" of each Mounting Screw

exposed. 

Hang the RO System Head

on the Mounting Screws

C

.

Be sure that all electrical appliances and outlets are turned off at the 
circuit breaker before working in cabinet area.

WARNING

Please wear safety glasses to protect 
eyes when drilling.

CAUTION

Summary of Contents for PTL RO System




















Reviews: