Spectrum PTL RO System Installation Instructions Manual Download Page 13

Page: 13 / 19

Twist-Lock

™

Filter Replacement

Turn off the cold water shut-off valve to the RO Filter System Assembly.

Turn each Twist-Lock

™

Filter

from right to left until it releases. Gently pull down on each used Twist-Lock

™

Filter

to remove it from the RO System Head

. Discard the used Twist-Lock

™

Filters.

NOTE: Place a pan or bucket under the RO Filter System to catch any water drips.

Hold each new Twist-Lock

™

Filter with the label facing to the left slightly. The two nozzles on top of each Twist-Lock

™

Filter

should be toward the back of the Twist-Lock

™

Filter. If holding properly, the two extended flanges on top of the Twist-Lock

™

Filter

should be out to each side.

NOTE: When viewing the Twist-Lock™ RO System from the front, the

and

are both PTL-C

filters. These filters must be po-

sitioned on either side of the center position while the

is the PTL-RO or Membrane and must be positioned in the center position .

Lift each Twist-Lock

™

Filter straight up into the RO System Head

until the two nozzles seat into the ports and the two

extended flanges on top of the Twist-Lock

™

Filter are fully engaged into the RO System Head

Turn each Twist-Lock

™

Filter from left to right until it stops.

Turn on the cold water shut-off valve and the RO Tap and check for any leaks. If there are leaks, refer to the troubleshooting
information on page 15 of the installation instructions.

Pressure Test and purge system per Step 8.

Summary of Contents for PTL RO System




















Search results

Summary of Contents for PTL RO System

Reviews:

Related manuals for PTL RO System

Brands by name

Popular brands

Spectrum PTL RO System, Installation Instructions Manual

Search results

Summary of Contents for PTL RO System

Reviews:

Related manuals for PTL RO System

Brands by name

Popular brands