background image

0115348R3 Page 2 of 9

•  Read this owner’s manual before assembly or operation.

•  Do not allow children to move the lectern.

•  Proceed slowly and carefully when moving the lectern.

•  For indoor use only.  Do not install or store the lectern where it will be exposed 

to moisture.

•  Do not block the ventilation openings.

•  Avoid uneven loading of the equipment into the lectern.  Uneven weight 

distribution could cause the lectern to tip when the lectern is moving.

•  Do not allow anyone to sit, stand, or climb on the lectern.

•  Use a damp, soft-cloth, or sponge, with mild soap or detergent solution to clean 

dirty surfaces.  Do not use harsh solvents or abrasives.

•  This lectern is intended for institutional use.  It does not have any user-

serviceable parts or user-maintenance requirements.  If servicing is necessary, 

please contact Spectrum Industries for assistance.

Electrical Safety:

•  Do not plug the power cord into an extension cord.

•  Inspect power cords for damage before each use.  Do not use power cords 

that are damaged.

•  Unplug power cord from electrical outlet by gripping the cord.  Do not unplug 

the power cord by pulling only on the cord.

•  Do not step on, drive over, drag, or place objects on the power cord.

•  For added safety, plug the lectern into a grounded outlet controlled by a GFI 

(Ground Fault Interrupter) circuit breaker.

•  Electrical devices are not toys.  Children are often unaware of the hazards 

associated with electrical devices.  This lectern must always be used by 

adults or with adult supervision.

Warning

 - Relocating audio and/or video equipment to furniture not specifi cally 

designed to support audio and/or video equipment may result in death or 

serious injury due to the furnishing collapsing or over turning onto a child.

Warning

 - Death or serious injury may occur when children climb on audio 

and/or video equipment furniture.  A remote control or toys placed on the 

furnishing may encourage a child to climb on the furnishing and as a result the 

furnishing may tip over on to the child.

Important Safety and Care Instructions

Summary of Contents for Masters Interactive Lectern 55250TW










Reviews: