manualshive.com logo in svg

SpectraPure MaxPure MPRO-300 RO System, Installation And Operating Manual

Share
Download
SpectraPure MaxPure MPRO-300 RO System Installation And Operating Manual Download Page 4

SpectraPure

SpectraPure®Inc.

  

480.894.5437   Call us toll-free  1.800.685.2783    

2167 East Fifth St,    Tempe, Arizona   85281

®

4

The incoming feed water  from a cold supply  pipe valve is directed through 3/8” BLACK 
tubing and is first passed through a 1 micron Micro-Tec™ sediment pre-filter. This filter is 
used to remove excessive turbidity, sand, dust, silt etc.that may cause the carbon filter to 
plug up. The next two stages of filtration is a 5  and 1 micron carbon block pre-filter. These 
filters are used to remove organics and chlorine from the feed water that can damage the 
membrane. The final stage of the system is the R.O. membrane. A high rejection Thin Film 
Composite (TFC) membrane is used in this system. This removes as much as 98% of most 
inorganic salts, all micro-organisms and almost all high molecular weight organics in the 
water. 

Fig. A: Single-Membrane Filter 

TFC RO Membrane

1 micron 
Carbon Block 
Filter (CF-1-10)

1 micron 
MicroTec™
Sediment Pre-Filter
(SF-MT-1-10)

Pressure Gauge

SYSTEM DESCRIPTION :

5 micron 
Carbon Block 
Filter (CF-5-10)

3/8”
Tap Water
Input

3/8” BLACK LINE: Tap Water
1/4” BLUE LINE: Product Water
1/4” YELLOW LINE: Waste Water
         (Flow Restrictor is inside the
          Waste line)

Summary of Contents for MaxPure MPRO-300 RO System

















Reviews:

No comments

Brands by name

Popular brands

Load more brands