background image

SpectraLink Corporation 

Link Wireless Telephone User Guide 

detergent residue with a plain water dampened cloth. 

DO NOT IMMERSE THE DUAL 

CHARGING STAND IN WATER OR OTHER LIQUID.

 

The Battery Pack contacts may be cleaned with isopropyl (rubbing) alcohol applied with 
a Q-tip, cloth, or paper towel.

 

Do not push or pull the exposed Battery Pack contacts.

  DO 

NOT POUR LIQUIDS INTO THE SLOTS.

 

The Quick Charger 

The Quick Charger holds a single Battery Pack and can charge it in approximately one 
hour. 

Using the Quick Charger 

Place the Battery Pack on the charger by gently 
sliding the Pack upward into the charger in a 
manner similar to installing it on the Wireless 
Telephone. If placed correctly, the light on the 
Quick Charger will shine solid green. When the 
Pack is fully charged, the green light will begin 
to flash. 
Every 11th charge the Quick Charger will 
automatically recondition the Battery Pack, as 
indicated by the flashing amber light. This may 
take from three to six hours depending on the 
state of the Battery Pack. To enter or exit the 
reconditioning mode, press the 

MODE

 button 

while the Battery Pack is on the Quick Charger. 

Part Number: 72003551H.doc 

Page 6 

Summary of Contents for Link Wireless













Reviews: