SpectraLink Link Wireless User Manual Download Page 7

SpectraLink Corporation 

Link Wireless Telephone User Guide 

Charging the Wireless Telephone 

Chargers are shipped with the appropriate power supply for the site’s location. Connect 
the Stand or Charger to an appropriate wall outlet via its power supply and it’s ready for 
use. Chargers operate in a 50° to 85° F (10° to 30° C) environment. Do not expose them 
to freezing temperatures or direct sunlight. 

The Dual Charging Stand 

The SpectraLink Dual Charging Stand is a two-slot desktop charger designed to charge 
the Nickel Metal Hydride (NiMH) Battery Packs required to operate Wireless 

Telephones. Full charging is accomplished in 
approximately two hours. 
Only NiMH Battery Packs with a YELLOW label on the 
handset contact side may be charged in the Dual Charging 
Stand.  Nickel-Cadmium (NiCd) and older NiMH Battery 
Packs with a GREEN label will not charge. If the indicator 
light does not come on when a Wireless Telephone or 
Battery Pack is first placed in the Charger, check to make 
sure the Battery Pack has a YELLOW label. 
 
Do not place anything in the Dual Charging Stand other 
than the Wireless Telephone. You might damage the 
contacts. Bent contacts can keep the Wireless Telephone 
from charging. 

Using the Dual Charging Stand 

Place the Dual Charging Stand on a flat, horizontal surface. 
The user must end any call in progress by pressing the 

END

 key on the Wireless 

Telephone before placing the handset into the Charger.  Place the Wireless Telephone in 
the front compartment facing forward. It may be on or off during charging.  A spare 
Battery Pack may be placed in the rear slot.  Either slot can be chosen to take priority. 
The first Battery Pack placed into either slot is charged first.  
There are two indicator lights, one for each charging slot. Verify that the light for the 
corresponding slot comes on when a Wireless Telephone or Battery Pack is placed into a 
charging slot.  The light turns off when the Charger is finished charging or a short time 
after a fully charged Battery Pack is placed in a slot.  An indicator light will not come on 
when the slot is empty, when a Battery Pack is improperly seated or is the wrong type, or 
when the Charger has no power applied.  A fast flash indicates the Battery Pack is not 
charging and must be replaced.  

Cleaning the Dual Charging Stand 

Clean the Dual Charging Stand by wiping the surface with a clean, water-dampened cloth 
or paper towel. A mild detergent solution may be used. Be sure to wipe away any 

Part Number: 72003551H.doc 

Page 5 

Summary of Contents for Link Wireless













Reviews: