SpectraLink JPI300 Installation Manual Download Page 39

Page: 39 / 68

PN: 1725-36122-001_N.doc

System Installation

Facility Analysis

Check the site to be sure pre-installation work has been completed

correctly. This includes:



Location chosen for the shelves is adequate.



Rack (if rack mounted) is properly secured or backboard (if wall

mounted) is properly prepared.



Power is available.



Wiring to Base Station locations has been pulled and correctly

terminated.



Phone lines for the handsets are installed and properly

terminated.



Telephone system administrator is on-site to program the existing

telephone system.



If the work has not been completed, the Polycom Field Service

Engineer may leave the site and reschedule the installation when

the items have been completed or corrected, or may assist in

preparing the site.

Check Components

At the installation site, unpack the system carefully, verify that there

is no shipping damage, and store in a safe place. As the field service

engineer unpacks, he or she must confirm that contents are correct by

comparing with the shipping documents.

Before beginning the system installation, begin charging a
handset. The Battery Packs for the handsets are not charged when
shipped. At least one fully charged handset is required to test the
system.

Summary of Contents for JPI300





































































Search results

Summary of Contents for JPI300

Reviews:

Related manuals for JPI300

Brands by name

Popular brands

SpectraLink JPI300, Installation Manual

Search results

Summary of Contents for JPI300

Reviews:

Related manuals for JPI300

Brands by name

Popular brands