background image

VII.  LIMITED WARRANTY

For a period of 18 months from the date of original purchase, KB Electronics, Inc. will repair

or replace, without charge, devices which our examination proves to be defective in material

or workmanship.  This warranty is valid if the unit has not been tampered with by unauthorized

persons, misused, abused, or improperly installed and has been used in accordance with the

instructions and/or ratings supplied.  The foregoing is in lieu of any other warranty or guaran-

tee, expressed or implied.  KB Electronics, Inc. is not responsible for any expense, including

installation and removal, inconvenience, or consequential damage, including injury to any per-

son, caused by items of our manufacture or sale.  Some states do not allow certain exclusions

or limitations found in this warranty and therefore they may not apply to you.  In any event, the

total liability of KB Electronics, Inc., under any circumstance, shall not exceed the full purchase

price of this product.  (rev 2/2000)

(A40275) – Rev. C – 6/2001

KB Electronics, Inc.

12095 NW 39th Street, Coral Springs, FL 33065-2516 • (954) 346-4900 • Fax (954) 346-3377
Outside Florida Call TOLL FREE (800) 221-6570 • E-mail – [email protected]
www.kbelectronics.com

Summary of Contents for VARI-DRIVE KBWM-120

















Reviews: