background image

4

Important Notice:

This manual contains important information about the installation, operation and safe use of this product. 

This information should be given to the owner and/or operator of this equipment. 

WARNING: 

Before  Installing  this  product,  read  and  follow  all  warning  notices  and  instructions  which 

are  included.  Failure  to  follow  safety  warnings  and  instructions  can  result  in  severe  injury,  death,  or 

property damage. Call 1-800-223-8538 or visit www.usa.speck-pumps.com for additional copies of these 

instructions.

SUCTION HAZARD.

 Can cause serious injury or death. Do not use 

this pump for wading pools, shallow pools, or spas containing bottom 

drains, unless pump is connected to at least two (2) functioning suction 

outlets. 

WARNING:

  Pump  suction  is  hazardous  and  can  trap  and  drown  or 

disembowel bathers. Do not use or operate swimming pools, spas, or 

hot tubs if a suction outlet cover is missing, broken, or loose.

The following guidelines provide information for pump installation 

that minimizes risk of injury to users of pools, spas, and hot tubs:

Entrapment  Protection:

  The  pump  suction  system  must  provide 

protection against the hazards of suction entrapment.

Suction Outlet Covers:

 All suction outlets must have correctly installed, 

screw-fastened covers in place. All suction outlet (drain) covers must be 

maintained. Drain covers must be listed/certified to the latest published 

edition of ANSI/ASME A112.19.8 (ANSI/APSP-16, 2011). They must be 

replaced if cracked, broken, or missing. 

Number  of  Suction  Outlets  Per  Pump:

  Provide  at  least  two  (2)  

hydraulically-balanced  main  drains,  with  covers,  as  suction  for  each 

circulating pump suction line. The centers of the main drains (suction 

outlets) on any one (1) suction line must be at least three (3) feet apart, 

center to center.

READ THIS MANUAL CAREFULLY BEFORE USING THE SPECK PUMP

READ AND FOLLOW ALL INSTRUCTIONS!

DANGER: DO NOT BLOCK SUCTION

WARNING - Entrapment Prevention

Important Safety Instructions

Summary of Contents for Badu EcoM3V























Reviews: