background image

8999118EN: v1.1 21/12/2020 

 

4  

Original instructions (ENGLISH) 

Website:  www.spearheadmachinery.com 

 

 
 

Rolliflail Series Flail Mower 

 
This manual covers the Rolliflail group of flail mowers which are available in 1.5m, 1.8m and 2.1m cut widths. 
 
These medium-duty machines can be front, or rear mounted by decoupling and reversing the headstock 
which provides added functionality at no extra cost. 
 
In order to cater for the front and rear mounting options, these machines can be run at 540rpm or 1000rpm.  
Providing the tractor front and rear drive rotation is consistent with the machine drive rotation, the two drive 
speeds can be achieved by swapping the drive pulleys over. 
 
It is essential that the guards (including the roller) are always fitted during operation and that the machine is 
operated in line with the procedures and practices detailed in this manual.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

IMPORTANT 

 

This operator’s manual should be regarded as part of the machine.  Suppliers of both new and second-hand 

machines are advised to retain documentary evidence that this manual was provided with the machine. 

 

This machine is designed solely for ground vegetation control and must not be used for any other purpose.  

Use in any other way is considered as contrary to the intended use.  Compliance with, and strict adherence 

to, the conditions of operation, service, and repair, as specified by the manufacturer, also constitute 

essential elements of the intended use. 

 

This machine should be operated, serviced, and repaired only by persons who are familiar with its 

characteristics and who are acquainted with the relevant safety procedures. 

 

Accident prevention regulations, all other generally recognised regulations on safety and occupational 

medicine, and all road traffic regulations must always be observed. 

 

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any 

resulting damage or injury. 

 

It is potentially hazardous to fit or use any parts other than genuine 

Spearhead

 parts. 

 

The company disclaims all liability for the consequences of such use which, in addition, voids the machine 

warranty. 

 

Summary of Contents for ROLLIFLAIL 150






















































Reviews: