9
Original instructions
EN
cals and water fog.
Extinguishing method: Spray.
Combustion products:
Fumes, smoke, carbon
monoxide,sulphur oxides, aldehydes and other decom
-
position products in the case of incomplete combustion.
Forbidden media:
Water.
Measures against accidental release:
Protective measures:
Wear appropriate personal protec-
tion when cleaning up spills. For large spills use a pump
or a vacuum-truck and store in storage/salvage vessels.
For small spills soak up residue with an absorbent such
as clay, sand or other suitable material. Place in non-
leaking container and seal tightly for proper disposal.
Handling and storage:
Do not store in open or unlabeled containers. Store in
a cool, dry place with adequate ventilation. Keep away
from open flames and high temperature.
Empty used containers retain residue (liquid and/or va
-
pour) and can be dangerous. It is forbidden to pressur-
ize, cut, weld, braze, solder, drill, grind or expose such
containers to heat and flames.
Exposure control / Personal protection:
Provide adequate ventilation to control airborne concen
-
trations below the exposure guidelines/limits.
Wear appropriate respirator, chemical goggles, chemi
-
cally resistant to this oil protective gloves, protective
clothing and shoes. Wash hands with water an use cos-
metic to protect
VIII - Operating instructions
This power tool is supplied from single-phase alternat-
ing current mains only. It is double in¬sulated according
to EN 60745-1 and IEC 60745 and can be connected
to grounded or not grounded sockets. This power tool
is radio suppressed in compliance with EMC Directive
2004/108/EC.
The chain saw is designed for cutting wood (trees,
planks, laths, etc.).
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the power tool.
▪
Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
WARNING:
switch off and unplug the power
tool prior to any adjustment, servicing or maintenance.
▪
In case the work area is remote from the power
source, use as short as practicable extension cord
with proper cross-section. (1,5 mm
2
for extension
cords shorter than 25 m; 2,5 mm
2
or extension cords
long 25 m to 40 m).
▪
Use extension cords for outdoor use and marked
accordingly. Always fully unwind the extension cord
drum.
▪
It is recommended when operating outdoors and in
premises with high humidity to use a residual current
device (RCD) with a tripping current not exceeding
30 mA.
STARTING THE CHAIN SAW
1. Make sure the safety chain brake lever (1) is disen
-
gaged. The motor will not start if the chain brake is
in the engaged position. Disengage the chain brake
lever by pulling it backward toward the front handle
(Fig.7a)
An extension cord hook (7) is built-in the back han-
dle preventing extraction of the cord. To use this fea
-
ture, simple double the extension cord, about 30 cm
from the end, and insert it into the hole of the handle.
Hook the loop formed by doubling the cord over the
cord hook. Gently tug on the cord to ensure that it
is firmly retained in the handle. Plug the receptacle
end of the extension cord into the tool power supply
cord.
(Fig.8)
2. Grip the machine with both hands, left hand holding
the front handle (do not hold the chain brake) and
the right hand holding the rear handle. Press the
safety lock-off button (3), then fully press the switch
trigger (4) and hold in this position. The safety lock-
off button can be released now.
(Fig.7b, 7c).
NOTE:
It is not necessary to maintain pressure on the
lock-off button (3) once the switch trigger is squeezed
and the motor is running. The safety lock-off button (3) is
a safety device to avoid accidental starting.
STOPPING THE CHAIN SAW
The chain saw will stop automatically when the switch
trigger (4) is released. To restart the motor press the
safety lock-off button (3) and squeeze the switch trigger
(4).
CHAIN BRAKE FUNCTIONAL TEST
The chain brake is a safety mechanism actuated through
the front hand guard. When kickback occurs, chain stops
immediately.
The functional test should be carried out at regular in-
tervals to ensure it proper operation. The purpose of the
chain brake testing is to reduce the probability of injury
due to kickback.
Check the chain brake before starting to operate the
saw, after prolonged period of operation and always dur
-
ing maintenance.
WARNING:
If the chain and motor fail to stop
when the chain brake is engaged, take the saw to the
nearest authorized SPARKY service centre. Do not
use the saw with a faulty chain brake.
1. Make sure the safety chain brake lever is disen
-
gaged.
(Fig.9a)
2. Place the chain saw on any suitable flat surface.
3. Plug the machine into the supply source.
4. Grasp the front handle with your left hand (do not
hold the chain brake). Thumb and fingers should
encircle the handle.
pages-TV-2245.indd 9
15.5.2012 г. 09:59:28 ч.
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
