5
Original instructions
EN
g)
If devices are provided for the connec-
tion of dust extraction and collection fa-
cilities, ensure these are connected and
properly used.
Use of dust collection can
reduce dust-related hazards.
4) Power tool use and care
a)
Do not force the power tool. Use the cor-
rect power tool for your application.
The
correct power tool will do the job better and
safer at the rate for which it was designed.
b)
Do not use the power tool if the switch
does not turn it on and off.
Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c)
Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or stor-
ing power tools.
Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d)
Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e)
Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool’s op-
eration. If damaged, have the power tool
repaired before use.
Many accidents are
caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g)
Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed.
Use of the power tool for op-
erations different from those intended could
result in a hazardous situation.
5) Service
a)
Have your power tool serviced by a
qualified repair person using only iden
-
tical replacement parts.
This will ensure
that the safety of the power tool is main-
tained.
b)
The replacement of the plug or the sup-
ply cord shall be always performed by
the power tool manufacturer or in au-
thorised service centre.
IV - Wet stone polisher
and sander safety
warnings
Safety Warnings Common for Grinding,
Sanding, Wire Brushing, Polishing or
Abrasive Cutting-Off Operations:
а)
This power tool is intended to func-
tion as a grinder, sander, wire brush,
polisher or cut-off tool. Read all safety
warnings, instructions, illustrations and
specifications provided with this power
tool.
Failure to follow all instructions listed
below may result in electric shock, fire and/
or serious injury.
b)
Operations such as grinding and abra-
sive cutting, sanding, operation with
diamond discs and circular blades are
not recommended to be performed with
this power tool.
Operations for which the
power tool was not designed may create a
hazard and cause personal injury.
c)
Do not use accessories which are
not specifically designed and recom
-
mended by the tool manufacturer.
Just
because the accessory can be attached to
your power tool, it does not assure safe op-
eration.
d)
The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool.
Accessories
running faster than their rated speed can
break and fly apart.
e)
The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
In-
correctly sized accessories cannot be ad-
equately guarded or controlled.
f)
The arbour size of wheels, flanges,
backing pads or any other accessory
must properly fit the spindle of the pow
-
er tool.
Accessories with arbour holes that
do not match the mounting hardware of the
power tool will run out of balance, vibrate
excessively and may cause loss of control.
g)
Do not use a damaged accessory. Be-
fore each use inspect the accessory
such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or
cracked wires. If power tool or acces-
sory is dropped, inspect for damage or
install an undamaged accessory. After
