manualshive.com logo in svg

SP VirTis BenchTop 2K, Operator'S Manual

Share
Download
SP VirTis BenchTop 2K Operator'S Manual Download Page 15

VirTis BenchTop 2K, 4K and 6K 

Installation and Setup 

 

Revision 004, 12/09 

 

5

 

© SP Industries, Inc. 2009 

10.

 

Plug the vacuum pump into the receptacle marked VACUUM PUMP on the 
back of the unit. The receptacle is an IEC universal outlet. This allows you to 
control the pump using the Sentry 2.0. The voltage, phase and frequency of 
the vacuum pump must match the voltage, phase and frequency specified on 
the rear panel of the freeze dryer.

 

Note:

 You can power your vacuum pump from a wall socket if it does not have an IEC 

connector, but you will not be able to control the pump from the Sentry 2.0 Controller. 
Only a qualified electrician should perform installation of an IEC connector. The pump 
used should not exceed the amperage listed on the BenchTop serial tag. 

11.

 

Enable power to the vacuum pump by switching the pump’s circuit breaker to 
the on position. 

Oil Mist Eliminators 

To reduce fumes from the vacuum pump and/or vent the vacuum exhaust externally, 
SP Industries recommends the installation an Oil Mist Eliminator (OME).  

Related Parts 

•

 

Oil Mist Eliminator, Plastic for Oerlikon Leybold TRIVAC E D2.5E Vacuum 
Pump (P/N 414203).  

Summary of Contents for VirTis BenchTop 2K

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands