manualshive.com logo in svg

Sovema FC-2 180, Operation & Maintenance Manual, Page: 23 / 39

Share
Download
Sovema FC-2 180 Operation & Maintenance Manual Download Page 23

OPERATION & MAINTENANCE MANUAL 

              page 21                                                              Release 2017

DISCONNECTING THE MACHINE

The disconnection of the implement from the tractor must be carried out on a flat surface.
It’s a dangerous operation. Please read the following instruction carefully.

•

While remaining in the tractor seat, put the tractor PTO in neutral.

•

When  the  rotor  has  completely  stopped,  turn  off  the  engine  and  set  the  parking
brakes.

•

Get  off  of  the  tractor,  remove  the  pin  from  the  top  plates  of  the  machine  after
removing the safety key from the pin. Then, proceed to remove the third point.

•

Remove  the  pin  from  the  lower  plates  of  the  implement  after  removing  the  safety
key from the pin. Then, disconnect the lifting arms from the machine.

•

Remove the PTO Shaft.

Always check the tractor’s PTO is in neutral before dis-

connecting the PTO shaft!

Summary of Contents for FC-2 180








































Reviews:

No comments