manualshive.com logo in svg

Sovema FC-2 180, Operation & Maintenance Manual, Page: 14 / 39

Share
Download
Sovema FC-2 180 Operation & Maintenance Manual Download Page 14

OPERATION & MAINTENANCE MANUAL 

              page 12                                                              Release 2017

CONNECTING THE MACHINE

The  machines  described  in  this  manual  do  apply  to  any  kind  of  tractor  provided  of
universal three-point hitch.

The characteristics (length, diameter of the holes for the lifting pins) of the tractor's lifting
arms depend on the type of tractor, therefore it is necessary to prepare the machine in
order to properly hitch the implement.

Before  connecting  the  machine  to  the  tractor  you  must  make  sure  that  the  engine  is
turned off, brakes are locked and the ignition key is removed.

This operation must be performed on a flat area as it is very dangerous.

Do not allow anyone between tractor and implement
while the engine is running.

Follow these instructions:

•

Connect the two drawbar of the tractor to the lower plates of the mower by using 
two pins and two cotter keys to lock the pins in place (fig. 1).

PLATES

LOWER
PLATES

  Fig.1

UPPER

Summary of Contents for FC-2 180








































Reviews:

No comments