background image

Questions? Call Toll Free at 1-800-737-2112 

 

Copyright © 2011 MAT Engine Technologies, LLC

PROBLEM

POSSIBLE CAUSE(S)

SOLLUTION(S)

Engine will not start.

1. Ignition Switch in the “OFF” position.

2. Engine flooded.

3. Fuel Tank empty.

4. Spark Plug not firing.

5. Fuel not reaching carburetor.

6. Carburetor requires adjustment.

1. Move ignition switch to the ON position.

2. See 

Starting a Flooded Engine

 in 

OPERATION

 section.

3. Fill tank with correct fuel mixture.

4. Replace Spark Plug.

5. Check for kinked or split fuel line; repair 

or replace.

6. Contact a qualified service center.

Engine will not accelerate, lacks 

power or stalls.

1. Grass wrapped around Trimmer Head.

2. Air filter dirty.

3. Spark plug fouled.

4. Carburetor requires adjustment.

5. Carbon build-up on muffler outlet 

screen.

6. Compression low.

1. Clear debris and grass from Trimmer Head.

2. Clean air filter.

3. Clean or replace plug

4. Contact a qualified service center.

5. Contact a qualified service center.

6. Contact a qualified service center.

Engine smokes excessively.

1. Fuel mixture incorrect.

2. Air filter dirty.

3. Carburetor requires adjustment.

1. Empty Fuel Tank and refill with correct fuel 

mixture.

2. Clean or replace air filter.

3. Contact a qualified service center.

Engine runs hot.

1. Fuel mixture incorrect.

2. Spark Plug incorrect.

3. Carburetor requires adjustment.

4. Carbon build-up on muffler outlet 

screen.

1. See 

Mixing Fuel / 2-Cycle Oil

 in 

OPERATION

 section.

2. Replace with correct Spark Plug.

3.  Contact a qualified service center.

4.  Contact a qualified service center.

Engine will not idle properly.

1. Carburetor requires adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. Contact a qualified service center.

2. Contact a qualified service center.

3. Contact a qualified service center.

Troubleshooting

• Save all instructions 

You  may  have  further  questions  about  assembling,  operating,  or  maintaining  this Trimmer.  If  so,  you  can  contact  our 

Technical Service Department at 1-800-737-2112 (English only). 

You may also write to:

METL Corporate Office - CORRESPONDENCE ONLY
ATTN: Technical Service – METL
6700 Wildlife Way
Long Grove, IL  60047

Technical Service

 

11 

When contacting the Technical Service Department, have 
ready:

• Your Name

• Your Address

• Your Phone Number

• Model Number of Product

• Date of Purchase (include copy of receipt for written requests)

If you need assistance or have any questions, 
CALL TOLL FREE: 1-800–737-2112

Summary of Contents for S-HLT-2515-CB



















Reviews: