background image

Questions? Call Toll Free at 1-800-737-2112 

 

Copyright © 2011 MAT Engine Technologies, LLC

Warranty 

(Continued)

• Save all instructions 

Emission Warranty Parts List:

The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such 

warranty coverage if 

METL

 demonstrates that the engine has been abused, neglected, or improperly maintained, and that 

such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part. That 

notwithstanding, any adjustment of a component that has a factory installed, and properly operating, adjustment limiting 

device is still eligible for warranty coverage. The following emissions warranty parts list is covered.

(1) Fuel Metering System:

  (a) Gasoline carburetor assembly and its internal  

   

components (if so equipped)

  (b) Fuel filter (if so equipped)

  (c) Carburetor gaskets

  (d) Fuel pump (if so equipped)

(2) Air Induction System including:

  (a) Intake pipe/manifold

  (b) Air cleaner

(3) Ignition System including:

  (a) Spark plug 

  (b) Ignition module/coil

(4) Catalytic Muffler Assembly (if so equipped) including:

  (a) Muffler gasket

  (b) Exhaust manifold

(5) Crankcase Breather Assembly including:

  (a) Breather connection tube.

(6) Miscellaneous items Used in Above Systems including:

  (a) Switches

  (b) Hoses, belts, connectors, and assemblies.

 

15 

When the engine is used at a region where the altitude is over 3000 foot, a High Altitude Kit may be required to meet proper 

engine performance and emission control. Contact the Toll Free service phone number below for part replacement at the 

authorized service dealership. 

Operating the engine with the wrong engine configuration at a given altitude may increase its emission and decrease fuel 

efficiency and performance.

Summary of Contents for S-HLT-2515-CB



















Reviews: